IDES Prospector Already have an account? Login Here

IDES

Tecomid NA NA40 GR30 BK IH

Polyamide 66

Glass Fiber Reinforcement, 30%

Supplied by Eurotec Engineering Plastics

The technical datasheet with complete property values for Tecomid NA NA40 GR30 BK IH is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Europe
  
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Appearance 
  • Black
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Water Absorption (Equilibrium, 73°F, 50% RH)
%
 ISO 62
Viscosity Number (96% H2SO4 (Sulphuric Acid))
cm³/g
 ISO 307
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2/5
Tensile Stress (Break, 73°F)
psi
 ISO 527-2/5
Tensile Strain (Break, 73°F)
%
 ISO 527-2/5
Flexural Modulus 2 (73°F)
psi
 ISO 178
Flexural Strength 2 (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Notched Izod Impact Strength
     ISO 180/1A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Unnotched Izod Impact Strength
     ISO 180/1U
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B
Melting Temperature
°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0630 in
 
  
0.126 in
 
  
Additional Information
Moisture Content, ISO 960: <0.2%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Tecomid NA NA40 GR30 BK IH, Tecomid NA , TecomidNANA40GR30BKIH, TecomidNA, NANA 40 GR 30 BK IH, NANA40 GR30 BK IH, NANA40, NA, NA 40 GR 30 BK IH, NANA40GR30BKIH, NA40 GR30 BK IH, NA40, 40GR, GR30, 30BK, BKIH, NA40GR30BKIH, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Eurotec, Polyamide66, Nylon66, 40NA, 40NANA
Generic Name
Generic Name may also be described by the following terms: PA66.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Holding Pressure
psi
  
Injection Notes
Back Pressure: Low
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.