Tecomid NA NA43 GR30 NL Eurotec Polyamide 66 (Glass Fiber Reinforcement, 30%)

General

Material Status

Commercial: Active

Availability

Africa & Middle East

Europe

Filler / Reinforcement

Glass Fiber Reinforcement, 30% Filler by Weight

Appearance

Natural Color

Forms

Pellets

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Water Absorption (Equilibrium, 73°F, 50% RH)		%	ISO 62
Viscosity Number (96% H2SO4 (Sulphuric Acid))		cm³/g	ISO 307
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (73°F)		psi	ISO 527-2/5
Tensile Stress (Break, 73°F)		psi	ISO 527-2/5
Tensile Strain (Break, 73°F)		%	ISO 527-2/5
Flexural Modulus² (73°F)		psi	ISO 178
Flexural Strength² (73°F)		psi	ISO 178
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength			ISO 179/1eA
-22°F		ft·lb/in²
73°F		ft·lb/in²
Charpy Unnotched Impact Strength			ISO 179/1eU
-22°F		ft·lb/in²
73°F		ft·lb/in²
Notched Izod Impact Strength			ISO 180/1A
-22°F		ft·lb/in²
73°F		ft·lb/in²
Unnotched Izod Impact Strength			ISO 180/1U
-22°F		ft·lb/in²
73°F		ft·lb/in²
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature
66 psi, Unannealed		°F	ISO 75-2/B
264 psi, Unannealed		°F	ISO 75-2/A
Vicat Softening Temperature		°F	ISO 306/B
Melting Temperature		°F
Electrical	Nominal Value	Unit	Test Method
Surface Resistivity		ohms	IEC 60093
Volume Resistivity		ohm·cm	IEC 60093
Flammability	Nominal Value	Unit	Test Method
Flame Rating - UL			UL 94
0.0630 in
0.126 in
Glow Wire Flammability Index (0.0787 in)		°F	IEC 60695-2-12
Additional Information
Moisture Content, ISO 960: <0.2%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Tecomid NA NA43 GR30 NL, Tecomid NA , TecomidNANA43GR30NL, TecomidNA, NANA 43 GR 30 NL, NANA43 GR30 NL, NANA43, NA, NA 43 GR 30 NL, NANA43GR30NL, NA43 GR30 NL, NA43, 43GR, GR30, 30NL, NA43GR30NL, Polyamide 66, Nylon 66, Polyamide, Nylon, pa66, Eurotec, Polyamide66, Nylon66, 43NA, 43NANA
Generic Name
Generic Name may also be described by the following terms: PA66.

Injection	Nominal Value	Unit
Drying Temperature		°F
Drying Time		hr
Suggested Max Moisture		%
Front Temperature		°F
Processing (Melt) Temp		°F
Mold Temperature		°F
Injection Pressure		psi
Injection Rate
Holding Pressure		psi
Injection Notes
Back Pressure: Low

Notes

¹Typical properties: these are not to be construed as specifications.

²0.079 in/min

Tecomid NA NA43 GR30 NL

Polyamide 66

Glass Fiber Reinforcement, 30%

Supplied by Eurotec Engineering Plastics