IDES Prospector Already have an account? Login Here

IDES

Xantar® MX 2034

Polycarbonate

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for Xantar® MX 2034 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Mold Release
  • UV Stabilizer
  
Features 
  • Low Viscosity
RoHS Compliance 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg)
in³/10min
 ISO 1133
Molding Shrinkage - Flow
%
 ISO 294-4
Water Absorption (Saturation, 73°F)
%
 ISO 62
Limiting Viscosity Number
in³/lb
 ISO 1628-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain (Yield)
%
 ISO 527-2
Nominal Tensile Strain at Break
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength
psi
 ISO 178
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ISO 2039-2
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
Ball Pressure Test (257°F)
 
 IEC 60695-10-2
CLTE - Flow
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Dissipation Factor
     IEC 60250
100 Hz
 
  
1 MHz
 
  
Comparative Tracking Index
V
 IEC 60112
Electric Strength
V/mil
 IEC 60243-1
Optical
Nominal Value
Unit
Test Method
Transmittance
%
 ASTM D1003
Fill Analysis
Nominal Value
Unit
Test Method
Thermal Conductivity of Melt
Btu·in/hr/ft²/°F
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Xantar® MX 2034, Xantar MX 2034, Xantar® , Xantar, XantarMX2034, MX 2034, MX2034, Polycarbonate, PC, Mitsubishi EP, 2034MX
Features
Features may also be described by the following terms: Low Viscosity.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Shot Size
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw L/D Ratio
 
  
Screw Compression Ratio
 
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.