IDES Prospector Already have an account? Login Here

IDES

Terlux® 2812 TR Q434

Methyl Methacrylate / ABS

Supplied by Styrolution

The technical datasheet with complete property values for Terlux® 2812 TR Q434 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Terlux® 2812TR Q434 is a new grade with enhanced toughness.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Toughness
Agency Ratings 
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (220°C/10.0 kg)
in³/10min
 ISO 1133
Molding Shrinkage - Flow
%
 ISO 294-4
Water Absorption
     ISO 62
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2/50
Tensile Strain (Yield, 73°F)
%
 ISO 527-2/50
Nominal Tensile Strain at Break (73°F)
%
 ISO 527-2/50
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/1eU
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 358/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
CLTE - Flow (73 to 176°F)
in/in/°F
 ISO 11359-2
Thermal Conductivity
Btu·in/hr/ft²/°F
 ISO 8302
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity
     IEC 60250
73°F, 100 Hz
 
  
73°F, 1 MHz
 
  
Dissipation Factor
     IEC 60250
73°F, 100 Hz
 
  
73°F, 1 MHz
 
  
Electric Strength (73°F, 0.0394 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Additional Information
The value listed as Thermal Conductivity, ISO 8302, was tested in accordance with DIN 52612-2.
Electric Strength, IEC 60243-1, K20/P50, 1mm, 23°C: 37 kV/mm
Maximum Service Temperature (Short Cycle Operation): 75°C
Refractive Index, ISO 489: 1.54
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Terlux® 2812 TR Q434, Terlux 2812 TR Q434, Terlux® , Terlux, Terlux2812TRQ434, 2812 TR Q 434, 2812 TR Q434, 2812TR, TRQ, Q434, 2812TRQ434, Methyl Methacrylate / ABS, Methyl Methacrylate ABS, Methyl Methacrylate : ABS, Methyl Methacrylate + ABS, Methyl Methacrylate - ABS, Methyl Methacrylate _ ABS, Methyl Methacrylate ABS, MABS, Methyl Methacrylate, MM, Styrolution, MethylMethacrylateABS, MethylMethacrylate, MethylMethacrylate_ABS, TR2812
Features
Features may also be described by the following terms: Good Toughness, Tough.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.