IDES Prospector Already have an account? Login Here

IDES

Geon™ Vinyl Rigid Extrusion 87547

Rigid Polyvinyl Chloride

Supplied by PolyOne Corporation

The technical datasheet with complete property values for Geon™ Vinyl Rigid Extrusion 87547 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • High Flow
  • High Impact Resistance
  
Uses 
  • Profiles
Appearance 
  • Clear/Transparent
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
PVC Cell Classification
 
 ASTM D1784
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 2 (Yield)
psi
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256A
73°F, 0.125 in, Injection Molded
ft·lb/in
  
Across Flow: 73°F, 0.125 in, Compression Molded
ft·lb/in
  
Flow: 73°F, 0.125 in, Compression Molded
ft·lb/in
  
Drop Impact Resistance
     ASTM D4226
73°F 3
in·lb/mil
  
73°F 4
in·lb/mil
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, 15 sec)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.125 in)
°F
 ASTM D648
CLTE - Flow
in/in/°F
 ASTM D696
Additional Information
Note: The Cell Classification was determined using the notched Izod test with injection molded samples.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Geon™ Vinyl Rigid Extrusion 87547, Geon Vinyl Rigid Extrusion 87547, Geon™ Vinyl Rigid Extrusion , Geon Vinyl Rigid Extrusion, GeonVinylRigidExtrusion87547, GeonVinylRigidExtrusion, Extrusion 87547, Extrusion87547, Extrusion, 87547, Polyvinyl Chloride, Rigid, Polyvinyl Chloride Rigid, PVC, Rigid, PVC Rigid, Polyvinyl Chloride, PVC, PolyOne, PolyvinylChlorideRigid, PVCRigid, PolyvinylChloride, 87547Extrusion
Features
Features may also be described by the following terms: High Flow, High Melt, High MFI, High Impact Resistance.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 0.20 in/min
3Procedure A, C.125 Dart
4Procedure B, C.125 Dart
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.