IDES Prospector Already have an account? Login Here

IDES

SABIC® LLDPE R50035E

Linear Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LLDPE R50035E is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LLDPE R50035E is a LLDPE copolymer that is designed to provide excellent stress crack resistance, excellent mechanical properties with high rigidity, toughness, gloss and very low warpage. The resin contains UV stabilizer. It is recommended that SABIC® LLDPE R50035E is grinded before use in rotational moulding applications.

SABIC® LLDPE R50035E is desinged for rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Its excellent mechanical properties and low warpage makes it suitable for injection moulding applications such as screw closures, caps and housewares. SABIC® LLDPE R50035E is UV stabilised; that provides excellent protection for the final product.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/
medical applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • UV Stabilizer
Features 
  • Good Toughness
  • High ESCR (Stress Crack Resist.)
  • High Gloss
  • High Rigidity
  • Low Warpage
Uses 
  • Agricultural Tanks
  • Caps
  • Closures
  • Drums
  • Household Goods
  • Tanks
  • Waste Containers
Forms 
  • Pellets
Processing Method 
  • Injection Molding
  • Rotational Molding
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (100% Igepal, Compression Molded, F50)
hr
 ASTM D1693B
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Elongation (Break, Compression Molded)
%
 ASTM D638
Flexural Modulus - 1% Secant (Compression Molded)
psi
 ASTM D790
Flexural Strength (Compression Molded)
psi
 ASTM D790
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
 ASTM D746
Vicat Softening Temperature
°F
 ASTM D1525
Additional Information
Oven Temperature: 315°C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LLDPE R50035E, SABIC LLDPE R50035E, SABIC® LLDPE , SABIC LLDPE, SABICLLDPER50035E, SABICLLDPE, LLDPER 50035 E, LLDPER50035E, LLDPER50035, LLDPE, R 50035 E, R50035E, R50035, 50035E, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, SABIC, PolyethyleneLinearLowDensity, 50035R, 50035LLDPER
Features
Features may also be described by the following terms: High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, High Gloss, High Rigidity, Good Toughness, Tough, Low Warpage, Low Warp.
Uses
Uses may also be described by the following terms: Agricultural Tanks, Closure Caps, Caps, Cap, Household Goods, Housewares, Waste Containers, Waste Container.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.