IDES Prospector Already have an account? Login Here

IDES

Indothene LL LL 36RA045 UV

Linear Low Density Polyethylene

Supplied by Reliance Industries Limited

The technical datasheet with complete property values for Indothene LL LL 36RA045 UV is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Indothene-LL LL36RA045UV is a Linear Medium Density Polyethylene produced by gas phase fluidised bed process using butene as comonomer. This grade is stabilised with appropriate quantity of HALS to give a long service with continuos outdoor exposure with or without blending of any carbon black.
Indothene-LL LL36RA045UV when pulverised into 20-30 mesh powder offers, good processability. This grade has very good Environmental Stress Crack Resistance (ESCR) and a combination of Hardness and Impact strength. This grade contains normal dose of AO and high dose of UV stabiliser.

FOOD CONTACT APPLICATIONS :
This grade meets the requirements of Indian Standard IS-10146-1982 on "Polyethylene for its safe use in contact with food stuffs, pharmaceuticals and drinking water". It also conforms to the positive list of constituents as approved in IS:10141:1982. The antioxidant content of the grade is <3000 ppm.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  
Additive 
  • Unspecified Stabilizer
  • UV Stabilizer
  
Features 
  • Butene Comonomer
  • Food Contact Acceptable
  • Good Stability
  • Good UV Resistance
  • Good Weather Resistance
  • High ESCR (Stress Crack Resist.)
  • High Hardness
  • High Impact Resistance
Uses 
  • Agricultural Tanks
  • Containers
  • Shipping Containers
  • Tanks
  
Appearance 
  • Natural Color
Forms 
  • Pellets
Processing Method 
  • Rotational Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Environmental Stress-Cracking Resistance (10% Igepal, F50)
hr
 ASTM D1693
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield, 0.0787 in, Compression Molded)
psi
 ASTM D638
Tensile Elongation (Yield)
%
 ASTM D638
Flexural Modulus (0.126 in, Compression Molded)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in, Injection Molded)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
  
Additional Information
Enviro. Stress Crack Res, F50, 10% Igepal: > 350 hrs.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Indothene LL LL 36RA045 UV, Indothene LL , IndotheneLLLL36RA045UV, IndotheneLL, LLLL 36 RA 045 UV, LLLL 36RA045 UV, LLLL36, LL, LL 36 RA 045 UV, LLLL36RA045UV, LL 36RA045 UV, LL36, 36RA, RA045, 045UV, LL36RA045UV, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Reliance, PolyethyleneLinearLowDensity, 36LL, 36LLLL
Features
Features may also be described by the following terms: Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Butene Comonomer, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, High Hardness, Hard, High Impact Resistance, Good Stability, Good Weather Resistance, Weather Resistant.
Uses
Uses may also be described by the following terms: Agricultural Tanks, Shipping Containers, Shipping Container.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.