IDES Prospector Already have an account? Login Here

IDES

HIDEN® E308U

High Density Polyethylene

Supplied by YUHWA Korea Petrochemical Ind. Co., Ltd.

The technical datasheet with complete property values for HIDEN® E308U is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • Good Stretchability
  • Good Weather Resistance
  • High Tensile Strength
Uses 
  • Netting
  • Rope
  • Tape
Agency Ratings 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ASTM D1505
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525
Melting Temperature
°F
 DSC
CLTE - Flow
in/in/°F
 ASTM D696
Specific Heat
Btu/lb/°F
 ASTM C351
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength 2
V/mil
 ASTM D149
Dielectric Constant (1.00 GHz)
 
 ASTM D150
Dissipation Factor (1.00 GHz)
 
 ASTM D150
Additional Information
The values listed as Mold Shrink ASTM D955 and Specific Heat ASTM C351, were tested in accordance with KPIC method.
Brittleness Temperature, KPIC method: <-70E-4 cal cm/cm sec °C
Water Absorption @ 24 hrs, ASTM D570: <0.01%
Tensile Elongation at Break, ASTM D638: >500%
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HIDEN® E308U, HIDEN E308U, HIDEN® , HIDEN, HIDENE308U, E 308 U, E308U, E308, 308U, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Yuhwa, PolyethyleneHighDensity, 308E
Features
Features may also be described by the following terms: Good Stretchability, High Tensile Strength, Good Weather Resistance, Weather Resistant.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.