IDES Prospector Already have an account? Login Here

IDES

LAMIGAMID® 600

Acetal (POM) Copolymer

Supplied by Schwartz Technical Plastic

The technical datasheet with complete property values for LAMIGAMID® 600 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
  • North America
  
Uses 
  • Abrasion Resistant Liners
  • Bearings
  
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Water Absorption
     ISO 62
73°F, 24 hr
%
  
Saturation, 73°F
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Compressive Stress
     ISO 604
20% Strain
psi
  
10% Strain
psi
  
5% Strain
psi
  
Coefficient of Friction
     ASTM D1894
vs. Steel - Dynamic
 
  
vs. Steel - Static
 
  
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact Strength
ft·lb/in²
 ISO 180
Unnotched Izod Impact Strength
ft·lb/in²
 ISO 180
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Melting Temperature (DSC)
°F
 ISO 3146
CLTE - Flow (68 to 212°F)
in/in/°F
 ISO 11359-2
Specific Heat
Btu/lb/°F
 ASTM C351
Thermal Conductivity
Btu·in/hr/ft²/°F
 ISO 8302
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Dielectric Constant
 
 IEC 60250
Dissipation Factor
 
 IEC 60250
Electric Strength
V/mil
 IEC 60243-1
Additional Information
Creep Rate Stress, DIN 53444, 1% Elongation: 13 N/mm²
Creep Rate Stress, DIN 53444, 2% Elongation: 22 N/mm²
Friction Wear: 0.90 µm/Km
Coef of Friction, ASTM D1894, vs. Steel-Dynamic: 0.02 to 0.08
Penetration Resistance, DIN 53482: 1E15 ohm-cm
Creepage/leakage Resistance: KA3b
Safe Temperature Range, short periods: 140°C
Safe Temperature Range, permanent: -40° to 100°C
Unnotched Izod Impact, ISO 180: >90 kJ/m²
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: LAMIGAMID® 600, LAMIGAMID 600, LAMIGAMID® , LAMIGAMID, LAMIGAMID600, 600, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Schwartz, AcetalPOMCopolymer
Uses
Uses may also be described by the following terms: Abrasion Resistant Liners.
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.