IDES Prospector Already have an account? Login Here

IDES

OP - PPO PPOX-235

Polyphenylene Ether + PS

Supplied by Oxford Polymers

The technical datasheet with complete property values for OP - PPO PPOX-235 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • General Purpose
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (315°C/5.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield
psi
  
Break
psi
  
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (40°F)
ft·lb/in
 ASTM D256
Gardner Impact
in·lb
 ASTM D3029
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.125 in
°F
  
264 psi, Unannealed, 0.125 in
°F
  
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0625 in
 
  
0.125 in
 
  
Additional Information
Melt Mass -Flow Rate (MFR), ASTM D1238, 315°C/ 5.0kg: 12 to 18 g/10 min
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: OP - PPO PPOX-235, OP PPO PPOX235, OP - PPO , OP PPO, OP : PPO, OP / PPO, OP + PPO, OP _ PPO, OP PPO, OPPPOPPOX235, OPPPO, OP_PPO, PPOX, PPOPPOX-235, PPOPPOX235, PPOPPOX:235, PPOPPOX/235, PPOPPOX+235, PPOPPOX_235, PPOPPOX 235, PPOPPOX, PPOX-235, PPOX235, PPOX:235, PPOX/235, PPOX+235, PPOX_235, PPOX 235, Polyphenylene Ether + PS, Polyphenylene Ether PS, Polyphenylene Ether : PS, Polyphenylene Ether / PS, Polyphenylene Ether - PS, Polyphenylene Ether _ PS, Polyphenylene Ether PS, PPE+PS, PPEPS, PPE:PS, PPE/PS, PPE-PS, PPE_PS, PPE PS, Polyphenylene Ether, PPE, Oxford Polymers, PolyphenyleneEtherPS, PolyphenyleneEther, PolyphenyleneEther_PS, 235PPOX, 235PPOPPOX
Generic Name
Generic Name may also be described by the following terms: PPO.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.