IDES Prospector Already have an account? Login Here

IDES

LNP* Stat-Kon* 9X02785

Polycarbonate

Proprietary Filler

Supplied by SABIC Innovative Plastics Asia Pacific

The technical datasheet with complete property values for LNP* Stat-Kon* 9X02785 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LNP STAT-KON* 9X02785 is a compound based on Polycarbonate resin containing Proprietary Filler(s). Added features of this material include: Electrically Conductive.

Also known as: LNP* Stat-Kon* Compound PDX-D-02785
Product reorder name: 9X02785
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Filler / Reinforcement 
  • Proprietary Filler
Features 
  • Electrically Conductive
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
 ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
 ASTM D4812
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed, 0.126 in)
°F
 ASTM D648
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257
Volume Resistivity
ohm·cm
 ASTM D257
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics

Product names can be difficult to match. You may have searched any one of these terms to find this product: LNP* Stat-Kon* 9X02785, LNP StatKon 9X02785, LNP* Stat-Kon* , LNP StatKon, LNP* Stat:Kon*, LNP* Stat/Kon*, LNP* Stat+Kon*, LNP* Stat_Kon*, LNP* Stat Kon*, LNPStatKon9X02785, LNPStatKon, LNP Stat_Kon, LNP Stat Kon, LNPStat_Kon, 9 X 02785, 9X02785, 9X, X02785, Polycarbonate, PC, SABIC IP Asia, X9
Features
Features may also be described by the following terms: Electrically Conductive, Conducts Electricity, Conductive.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.