IDES Prospector Already have an account? Login Here

IDES

Bakelite® UP 3620

Polyester Alloy

Supplied by Hexion Specialty Chemicals GmbH

The technical datasheet with complete property values for Bakelite® UP 3620 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Surface Finish
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Apparent Density
g/cm³
 ISO 60
Molding Shrinkage - Flow
%
 ISO 294-4
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Stress (Yield)
psi
 ISO 527-2/5
Flexural Modulus
psi
 ISO 178
Flexural Strength 2
psi
 ISO 178
Compressive Stress - Flow
psi
 ISO 604
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/2eA
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179/2eU
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 961/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (1160 psi, Unannealed)
°F
 ISO 75-2/C
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Relative Permittivity (100 Hz)
 
 IEC 60250
Dissipation Factor (100 Hz)
 
 IEC 60250
Arc Resistance
sec
 ASTM D495
Arc Resistance (PLC)
 
 ASTM D495
Electric Strength (0.0394 in)
V/mil
 IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in, All colors)
 
 UL 94
Additional Information
Post Shrinkage, ISO 2577, Injection molding, Flow, 168h, 110°C: 0.25%
Post Shrinkage, ISO 2577, Compression molding, Flow, 168h, 110°C: 0.25%
Molding Shrinkage, ISO 2577, Flow, Injection molding: 0.75%
Molding Shrinkage, ISO 2577, Flow, Compression molding: 0.55%
Maximum Application Temperature, IEC 60216-P1/ DIN IEC 216-T1, <50h²: 190°C
Maximum Application Temperature, IEC 60216-P1/ DIN IEC 216-T1, <20000h²: 130°C
Proof Track Index, IEC 60112/ DIN IEC 112, Test liquid A: 600 PTI
Water Absorption, ISO 62, 24h/23°C: 75 mg
Arc Resistance, ASTM D495, 24h/23°C: 140 to 145 sec
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Bakelite® UP 3620, Bakelite UP 3620, Bakelite® , Bakelite, BakeliteUP3620, UP 3620, UP3620, Polyester Alloy, Polyester, Hexion GmbH, PolyesterAlloy, 3620UP
Features
Features may also be described by the following terms: Good Surface Finish.
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.