IDES Prospector Already have an account? Login Here

IDES

Rotec® ASA T 115/04

Acrylonitrile Styrene Acrylate

Supplied by ROMIRA GmbH

The technical datasheet with complete property values for Rotec® ASA T 115/04 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good UV Resistance
  • Good Weather Resistance
  • High Heat Resistance
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ISO 1133
Molding Shrinkage
%
 ISO 294-4
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2/1
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2/50
Tensile Strain (Break, 73°F)
%
 ISO 527-2/50
Flexural Modulus 2 (73°F)
psi
 ISO 178
Flexural Strength 2 (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179/1eU
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B50
CLTE - Flow (73 to 131°F)
in/in/°F
 ISO 11359-2
Thermal Conductivity
Btu·in/hr/ft²/°F
 ISO 8302
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0591 in)
 
 UL 94
Additional Information
The value listed as Thermal Conductivity ISO 8302, was tested in accordance with DIN 52612.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Rotec® ASA T 115/04, Rotec ASA T 11504, Rotec® ASA , Rotec ASA, RotecASAT11504, RotecASA, T 115, ASAT 115/04, ASAT 11504, ASAT 115:04, ASAT 115+04, ASAT 115-04, ASAT 115_04, ASAT 115 04, ASAT115, ASAT 115, ASAT11504, T 115/04, T 11504, T 115:04, T 115+04, T 115-04, T 115_04, T 115 04, T115, 11504, ASAT115_04, T11504, T115_04, Acrylonitrile Styrene Acrylate, ASA, Romira Euro, AcrylonitrileStyreneAcrylate, 115T, 115ASAT
Features
Features may also be described by the following terms: High Heat Resistance, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, Good Weather Resistance, Weather Resistant.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Injection Notes
Screw rotation speed: moderate to high
Back pressure: low to moderate
Injection pressure: tool depending
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Cylinder Zone 5 Temp.
°F
  
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
20.079 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.