IDES Prospector Already have an account? Login Here

IDES

Nilac AE/V0

Acrylonitrile Butadiene Styrene

Supplied by Soredi S.p.a.

The technical datasheet with complete property values for Nilac AE/V0 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
ABS high flow, flame retardant, with an UL 94 V0 at 1.6 mm rating, situable for the injection moulding, Official approved by the underwriters laboratories (yellow card)
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Flame Retardant
  • High Flow
  
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (Equilibrium, 73°F, 50% RH)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus 3
psi
 ASTM D790
Flexural Strength 3 (Break)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256
-4°F, 0.126 in
ft·lb/in
  
73°F, 0.126 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Vicat Softening Temperature
°F
 ASTM D1525 4
CLTE - Flow (73 to 131°F)
in/in/°F
 ISO 11359-2
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0630 in
 
  
0.126 in
 
  
Glow Wire Ignition Temperature
°F
 IEC 60695-2-13
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Nilac AE/V0, Nilac AEV0, Nilac , NilacAEV0, AE, AE V 0, AE/V0, AEV0, AE:V0, AE+V0, AE-V0, AE_V0, AE V0, AEV, V0, Acrylonitrile Butadiene Styrene, ABS, Soredi, AcrylonitrileButadieneStyrene, VAE
Features
Features may also be described by the following terms: High Flow, High Melt, High MFI.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): UL (1).
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
30.051 in/min
4Rate B (120°C/h), Loading 2 (50 N)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.