IDES Prospector Already have an account? Login Here

IDES

Elexar® EL-1392C

Thermoplastic Elastomer

Supplied by Teknor Apex Company

The technical datasheet with complete property values for Elexar® EL-1392C is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Uses 
  • Appliance Wire Insulation
  • Appliance Wire Jacketing
  • Cable Jacketing
  • Connectors
  • Flexible Cord Jacketing
  • Industrial Cable Insulation
  • Terminal Cable Jacketing
  • Underground Power Cable
  • Wire & Cable Applications
  • Wire Jacketing
Appearance 
  • Opaque
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
 
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
ASTM D792
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)
g/10 min
ASTM D1238
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress (100% Strain)
psi
ASTM D412
Tensile Strength (Break)
psi
ASTM D412
Tensile Elongation (Break)
%
ASTM D412
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 5 sec)
 
ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Brittleness Temperature
°F
ASTM D746
Aging
Nominal Value
Unit
Test Method
Change in Tensile Strength
    ASTM D471
277°F, 168 hr
%
 
316°F, 168 hr
%
 
Change in Ultimate Elongation
    ASTM D471
277°F, 168 hr
%
 
316°F, 168 hr
%
 
Electrical
Nominal Value
Unit
Test Method
Dielectric Strength
V/mil
ASTM D149
Dissipation Factor (77°F, 1 MHz)
 
ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0600 in)
 
UL 94
Oxygen Index
%
ASTM D2863
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Elexar® EL-1392C, Elexar EL1392C, Elexar® , Elexar, ElexarEL1392C, EL, EL 1392 C, EL-1392C, EL1392C, EL:1392C, EL/1392C, EL+1392C, EL_1392C, EL 1392C, EL1392, 1392C, Thermoplastic Elastomer, TPE, Teknor Apex, ThermoplasticElastomer, 1392EL
Uses
Uses may also be described by the following terms: Appliance Wire Insulation, Industrial Cable Insulation, Appliance Wire Jacketing, Flexible Cord Jacketing, Terminal Cable Jacketing, Wire and Cable Applications, Wire & Cable Applications.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Injection Pressure
psi
 
Injection Rate
 
 
Back Pressure
psi
 
Screw Speed
rpm
 
Cushion
in
 
Injection Notes
Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C).
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
 
Cylinder Zone 2 Temp.
°F
 
Cylinder Zone 3 Temp.
°F
 
Cylinder Zone 5 Temp.
°F
 
Die Temperature
°F
 
Extrusion Notes
Screw Speed: 30 to 100 rpm
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.