IDES Prospector Already have an account? Login Here

IDES

Iupital® F10-02

Acetal (POM) Copolymer

Supplied by Mitsubishi Engineering-Plastics Corp

The technical datasheet with complete property values for Iupital® F10-02 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Features 
  • Fatigue Resistant
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Creep Resistance
  • Good Moldability
  • Good Thermal Stability
  • High Viscosity
  • Low Friction
Uses 
  • Piping
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  • Pipe Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238, ISO 1133
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Molding Shrinkage - Flow
      
0.118 in
in/in
 ASTM D955
0.118 in
%
 ISO 294-4
Water Absorption (73°F, 24 hr)
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress
      
Yield
psi
 ISO 527-2
73°F
psi
 ASTM D638
Tensile Strain
      
Yield
%
 ISO 527-2
Break, 73°F
%
 ASTM D638
Nominal Tensile Strain at Break
%
 ISO 527-2
Flexural Modulus
      
73°F
psi
 ASTM D790
--
psi
 ISO 178
Flexural Strength
      
73°F
psi
 ASTM D790
--
psi
 ISO 178
Shear Strength
psi
 ASTM D732
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Charpy Unnotched Impact Strength (73°F)
ft·lb/in²
 ISO 179
Notched Izod Impact (0.126 in)
ft·lb/in
 ASTM D256
Tensile Impact Strength 2 (0.0630 in)
ft·lb/in²
 ASTM D1822
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
66 psi, Unannealed
°F
 ASTM D648
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ASTM D648
264 psi, Unannealed
°F
 ISO 75-2/A
Melting Temperature
      
--
°F
  
--
°F
 ISO 11357-3
CLTE
      
Flow: 68 to 176°F
in/in/°F
 ASTM D696
Flow
in/in/°F
 ISO 11359-2
Transverse
in/in/°F
 ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
 ASTM D257, IEC 60093
Volume Resistivity
ohm·cm
 ASTM D257, IEC 60093
Dielectric Strength
      
--
V/mil
 ASTM D149
0.0394 in
V/mil
 IEC 60243-1
0.118 in
V/mil
 IEC 60243-1
Dielectric Constant
      
1 MHz
 
 ASTM D150
100 Hz
 
 IEC 60250
1 MHz
 
 IEC 60250
Dissipation Factor
      
1 MHz
 
 ASTM D150, IEC 60250
100 Hz
 
 IEC 60250
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0315 in)
 
 UL 94
Related Terminology
This supplier and product may also be known by these terms: Lupital, Jupital

Product names can be difficult to match. You may have searched any one of these terms to find this product: Iupital® F10-02, Iupital F1002, Iupital® , Iupital, IupitalF1002, F 10, F 10 02, F10-02, F1002, F10:02, F10/02, F10+02, F10_02, F10 02, F10, 1002, Acetal Copolymer, Acetal Copolymer, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Mitsubishi EP, AcetalPOMCopolymer, 10F
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Good Chemical Resistance, Chemical Resistant, Good Creep Resistance, Creep Resistant, Low Friction, Good Moldability, Good Thermal Stability, High Viscosity.
Uses
Uses may also be described by the following terms: Piping, Pipe.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type S
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.