IDES Prospector Already have an account? Login Here

IDES

PRL AH-GP1

Acetal (POM) Homopolymer

Supplied by Polymer Resources Ltd.

The technical datasheet with complete property values for PRL AH-GP1 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Discontinued
Availability 
  • North America
Additive 
  • Heat Stabilizer
Features 
  • Good Melt Strength
  • Heat Stabilized
  • Homopolymer
  • Low Flow
  
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/1.05 kg)
g/10 min
 ASTM D1238
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
     ASTM D638
Yield, 0.125 in
psi
  
Break, 0.125 in
psi
  
Flexural Modulus (0.125 in)
psi
 ASTM D790
Flexural Strength (0.125 in)
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Gardner Impact (0.125 in)
in·lb
 ASTM D3029
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.125 in
°F
  
264 psi, Unannealed, 0.125 in
°F
  
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0625 in
 
  
0.125 in
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: PRL AH-GP1, PRL AHGP1, PRL , PRLAHGP1, AH, AH GP 1, AH-GP1, AHGP1, AH:GP1, AH/GP1, AH+GP1, AH_GP1, AH GP1, AHGP, GP1, Acetal Homopolymer, Acetal Homopolymer, Acetal (POM) Homopolymer, Acetal POM Homopolymer, Acetal, pom, Polymer Res, AcetalPOMHomopolymer, GPAH
Features
Features may also be described by the following terms: Low Flow, Low Melt, Low MFI, Good Melt Strength, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Drying Time, Maximum
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
Drying Temperature: do not exceed 8 hours
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.