IDES Prospector Already have an account? Login Here

IDES

INSPIRE™ 136

Polypropylene Impact Copolymer

Supplied by Braskem Europe GmbH

The technical datasheet with complete property values for INSPIRE™ 136 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
INSPIRE™ 136 Performance Polymer is a low gel resin developed for the manufacturing of films for quality applications. INSPIRE 136 combines good processability with good stiffness and low gel content. INSPIRE 136 can be used as a blend partner to make more effective films with blown or cast film technology.

Applications for INSPIRE™ 136 Performance Polymer:
  • blown film
  • cast film
  • food packaging
  • hygiene applications

Complies with:
  • European Commission Regulation (EU) No 10/2011
  • U.S. FDA FCN 843
  • Consult the regulations for complete details.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Agency Ratings 
 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Flexural Modulus (Injection Molded)
psi
 ISO 178
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Film Puncture Energy (2.0 mil)
in·lb
 ASTM D5748
Film Puncture Force (2.0 mil)
lbf
 ASTM D5748
Tensile Modulus
     ISO 527-3
2% Secant, MD: 2.0 mil, Blown Film
psi
  
2% Secant, TD: 2.0 mil, Blown Film
psi
  
Tensile Stress
     ISO 527-3
MD: Yield, 2.0 mil, Blown Film
psi
  
TD: Yield, 2.0 mil, Blown Film
psi
  
MD: Break, 2.0 mil, Blown Film
psi
  
TD: Break, 2.0 mil, Blown Film
psi
  
Tensile Elongation
     ISO 527-3
MD: Break, 2.0 mil, Blown Film
%
  
TD: Break, 2.0 mil, Blown Film
%
  
Dart Drop Impact (2.0 mil, Blown Film)
g
 ISO 7765-1/A
Elmendorf Tear Strength
     ASTM D1922
MD: 2.0 mil, Blown Film
g
  
TD: 2.0 mil, Blown Film
g
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 2 (66 psi, Unannealed)
°F
 ISO 75-2/B
Vicat Softening Temperature 2
°F
 ISO 306/A
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INSPIRE™ 136, INSPIRE 136, INSPIRE™ , INSPIRE, INSPIRE136, 136, Polypropylene Impact Copolymer, PP Impact Copolymer, Polypropylene, PP, Braskem EU, PolypropyleneImpactCopolymer, PPImpactCopolymer
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Fabrication Conditions for blown film:
Die gap: 1.0 mm
Melt Temperature: 230°C
Blow-up Ratio: 2.5:1
Notes
1Typical properties: these are not to be construed as specifications.
2Injection Molded
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.