IDES Prospector Already have an account? Login Here

IDES

INEOS LDPE 23H430

Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe

The technical datasheet with complete property values for INEOS LDPE 23H430 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Applications
23H430 is suitable for a variety of general-purpose packaging films, liners, carrier bags and fine shrink film. It is also recommended for cross-linked foam as well as for blow-moulding applications.

Benefits and Features
23H430 is an autoclave LDPE homopolymer. It offers the following properties:
  • Good strength and dart drop resistance
  • Good drawdown
  • Low tendency to block
If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Additive Free
  • Crosslinkable
  • Foamable
  • General Purpose
  • Good Drawdown
  • Good Strength
  • Homopolymer
Uses 
  • Bags
  • Film
  • Foam
  • Liners
  
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction (Blown Film)
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus - 1% Secant (2.0 mil, Blown Film)
psi
 ISO 1184
Tensile Stress
     ISO 1184
MD: Yield, 2.0 mil, Blown Film
psi
  
TD: Yield, 2.0 mil, Blown Film
psi
  
MD: Break, 2.0 mil, Blown Film
psi
  
TD: Break, 2.0 mil, Blown Film
psi
  
Tensile Elongation
     ISO 1184
MD: Break, 2.0 mil, Blown Film
%
  
TD: Break, 2.0 mil, Blown Film
%
  
Dart Drop Impact (2.0 mil, Blown Film)
g
 ASTM D1709A
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.97 mil, Blown Film)
 
 ASTM D2457
Haze (1.97 mil, Blown Film)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LDPE 23H430, INEOS LDPE , INEOSLDPE23H430, INEOSLDPE, LDPE 23 H 430, LDPE23H430, LDPE23, LDPE, 23 H 430, 23H430, 23H, H430, Polyethylene, Low Density, Polyethylene Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLowDensity, H23, 23LDPE
Features
Features may also be described by the following terms: Good Drawdown, Good draw down, Good Strength, Additive Free, No Additives.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.