IDES Prospector Already have an account? Login Here

IDES

U-polymer L-1003PA

Polyarylate

Supplied by UNITIKA Plastics Division

The technical datasheet with complete property values for U-polymer L-1003PA is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
P series resins are resins succeeding the characteristics of the neat polymer, U-100, and improved in flowability and optical properties. Among many super engineering plastics, the resins are few transparent polymer alloys that have heat resistance. The heat-stable P-series resins have variations different in heat resistance in the range from 150 to 175°C. There are few transparent heat-resistant resins among super engineering plastics, and thus P series resins are valuable. The resins have favorable weather resistance, and in particular, the P- 1001 resin is approved by SAE Standard (J576 and J578) and FMVSS Standard (108). Making the most of these characteristics, the resins may be used, for example, as the lenses for automobile lamps. High flow-type resins, P-1001A, and P-3001S, are also available for thin molding products.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • North America
  
Additive 
  • Lubricant
Features 
  • Amorphous
  • Good Creep Resistance
  • Good Dimensional Stability
  • Good Flow
  • Good Impact Resistance
  • Good Weather Resistance
  • Heat Stabilized
  • High Heat Resistance
  • Lubricated
  • Opticals
Uses 
  • Automotive Applications
Automotive Specifications 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.118 in)
in/in
 ASTM D955
Water Absorption (24 hr, 0.125 in)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Arc Resistance
sec
 ASTM D495
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: U-polymer L-1003PA, Upolymer L1003PA, U-polymer , Upolymer, U:polymer, U/polymer, U+polymer, U_polymer, U polymer, UpolymerL1003PA, L 1003 PA, L-1003PA, L1003PA, L:1003PA, L/1003PA, L+1003PA, L_1003PA, L 1003PA, L1003, 1003PA, Polyarylate, Unitika, 1003L
Features
Features may also be described by the following terms: High Heat Resistance, Good Creep Resistance, Creep Resistant, Good Impact Resistance, Good Dimensional Stability, Dimensionally Stable, Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Good Weather Resistance, Weather Resistant, Good Flow.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Automotive Specifications
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): SAE (1).
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.