IDES Prospector Already have an account? Login Here

IDES

LONGLITE® PBT 4120 FU

Polybutylene Terephthalate

Glass Fiber Reinforcement, 23%

Supplied by Chang Chun Plastics Co., LTD.

The technical datasheet with complete property values for LONGLITE® PBT 4120 FU is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PBT 20 % glass fiber reinforced injection moulding grade with flame retardant
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 23% Filler by Weight
Features 
  • Flame Retardant
  • Fuel Resistant
  • Good Chemical Resistance
  • Good Electrical Properties
  • Good Moldability
  • Good UV Resistance
  • Good Wear Resistance
  • Good Weather Resistance
  • Low Warpage
  • Oil Resistant
  • Solvent Resistant
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Water Absorption
      
24 hr
%
 ASTM D570
73°F, 24 hr
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
      
Yield
psi
 ISO 527-2
--
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638, ISO 527-2
Flexural Modulus
psi
 ASTM D790, ISO 178
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact 2
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Melting Temperature
°F
 DSC
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257, IEC 60093
Volume Resistivity
ohm·cm
 ASTM D257, IEC 60093
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149, IEC 60243-1
Dielectric Constant (60 Hz)
 
 IEC 60250
Dissipation Factor (60 Hz)
 
 IEC 60250
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0315 in)
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: LONGLITE® PBT 4120 FU , LONGLITE PBT 4120 FU, LONGLITE® PBT , LONGLITE PBT, LONGLITEPBT4120FU, LONGLITEPBT, PBT 4120 FU, PBT4120 FU, PBT4120, PBT, PBT4120FU, 4120 FU, 4120FU, Polybutylene Terephthalate, Polyester, Chang Chun, PolybutyleneTerephthalate, FU4120, 4120PBT
Features
Features may also be described by the following terms: Good Electrical Properties, Low Warpage, Low Warp, Good Chemical Resistance, Chemical Resistant, Good Weather Resistance, Weather Resistant, Good Wear Resistance, Wear Resistant, Good Moldability, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Holding Pressure
psi
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Product has to be dryed.
Notes
1Typical properties: these are not to be construed as specifications.
2250 mil Notch Depth
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.