IDES Prospector Already have an account? Login Here

IDES

LONGLITE® PMC T 33

Phenolic

Mineral Filler; Wood Flour

Supplied by Chang Chun Plastics Co., LTD.

The technical datasheet with complete property values for LONGLITE® PMC T 33 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PMC T 33 is a granular wood flour and mineral reinforced phenolic product for compression moulding
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Filler / Reinforcement 
  • Mineral Filler
  • Wood Flour
  
Features 
  • Fuel Resistant
  • Good Chemical Resistance
  • Good Electrical Properties
  • Good Moldability
  • Good Wear Resistance
  • Good Weather Resistance
  • High Heat Resistance
  • Oil Resistant
  • Solvent Resistant
Forms 
  • Pellets
Processing Method 
  • Compression Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage
%
 JIS K6915
Water Absorption
      
24 hr
%
 ASTM D570
73°F, 24 hr
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
      
Yield
psi
 ISO 527-2
--
psi
 ASTM D638
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.250 in)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Melting Temperature 2
°F
 ASTM D648
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257, IEC 60093
Volume Resistivity
ohm·cm
 ASTM D257, IEC 60093
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149, IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.250 in)
 
 UL 94
Additional Information
Monohole, CCP: 18 G
Density, ASTM D792 & ISO 1183: 1.36 to 1.37 g/cm³
Charpy Notched Impact Strength, ASTM D256: 2.7 kg cm/cm²

Compression Molding Conditions -
Preheating Temperature: 90 to 120°C
Mold Temperature: 150 to 180°C
Molding Presssure: 150 to 1000 bar
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: LONGLITE® PMC T 33, LONGLITE PMC T 33, LONGLITE® PMC , LONGLITE PMC, LONGLITEPMCT33, LONGLITEPMC, PMCT 33, PMC, PMCT33, T 33, T33, Phenolic, Chang Chun, 33T, 33PMCT
Features
Features may also be described by the following terms: Good Electrical Properties, High Heat Resistance, Good Chemical Resistance, Chemical Resistant, Good Weather Resistance, Weather Resistant, Good Wear Resistance, Wear Resistant, Good Moldability.
Notes
1Typical properties: these are not to be construed as specifications.
2Maximum application, 2 hours
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.