IDES Prospector Already have an account? Login Here

IDES

LONGLITE® PMC T 373 J60

Phenolic

Wood Flour

Supplied by Chang Chun Plastics Co., LTD.

The technical datasheet with complete property values for LONGLITE® PMC T 373 J60 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
PMC T 373 J60 is a granular wood flour reinforced phenolic product for injection moulding
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Filler / Reinforcement 
  • Wood Flour
Features 
  • Fuel Resistant
  • Good Chemical Resistance
  • Good Electrical Properties
  • Good Moldability
  • Good Wear Resistance
  • Good Weather Resistance
  • High Heat Resistance
  • Oil Resistant
  • Solvent Resistant
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Molding Shrinkage
%
 ISO 2577
Water Absorption
      
24 hr
%
 ASTM D570
73°F, 24 hr
%
 ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
      
Yield
psi
 ISO 527-2
--
psi
 ASTM D638
Flexural Strength
psi
 ASTM D790, ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.250 in)
ft·lb/in
 ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648, ISO 75-2/A
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 ASTM D257, IEC 60093
Volume Resistivity
ohm·cm
 ASTM D257, IEC 60093
Dielectric Strength (0.0787 in)
V/mil
 ASTM D149, IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0787 in)
 
 UL 94
Additional Information
Spiral Flow, CCP: 51 to 70 cm
Density, ASTM D792 & ISO 1183: 1.41 to 1.43 g/cm³
Maximum application temperature, IEC 60216-P1, 50 hr: 200°C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: LONGLITE® PMC T 373 J60, LONGLITE PMC T 373 J60, LONGLITE® PMC , LONGLITE PMC, LONGLITEPMCT373J60, LONGLITEPMC, PMCT 373 J 60, PMCT 373 J60, PMCT373, PMC, T 373 J 60, PMCT373J60, T 373 J60, T373, 373J, J60, T373J60, Phenolic, Chang Chun, 373T, 373PMCT
Features
Features may also be described by the following terms: Good Electrical Properties, High Heat Resistance, Good Chemical Resistance, Chemical Resistant, Good Weather Resistance, Weather Resistant, Good Wear Resistance, Wear Resistant, Good Moldability.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Injection Notes
Injection Time: 5 ± 2 sec
Hardening Time: 15 ± 5 sec
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.