IDES Prospector Already have an account? Login Here

IDES

Lubriblend® PA11 GF30 TL20 LE

Polyamide 11

Glass Fiber Reinforcement, 30%

Supplied by TP Composites, Inc.

The technical datasheet with complete property values for Lubriblend® PA11 GF30 TL20 LE is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 30% Filler by Weight
Additive 
  • Heat Stabilizer
  • PTFE Lubricant
  
Features 
  • Good Wear Resistance
  • Heat Stabilized
  • Low Extractables
  • Low Friction
  • Lubricated
Agency Ratings 
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow (0.125 in)
in/in
 ASTM D955
Water Absorption (24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength (Yield)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.125 in)
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed
°F
  
264 psi, Unannealed
°F
  
CLTE - Flow
in/in/°F
 ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength 2
V/mil
 ASTM D149
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Lubriblend® PA11 GF30 TL20 LE, Lubriblend PA11 GF30 TL20 LE, Lubriblend® , Lubriblend, LubriblendPA11GF30TL20LE, PA 11 GF 30 TL 20 LE, PA11 GF30 TL20 LE, PA11, 11GF, GF30, 30TL, TL20, 20LE, PA11GF30TL20LE, Polyamide 11, Nylon 11, Polyamide, Nylon, TP Compos, Polyamide11, Nylon11, 11PA
Generic Name
Generic Name may also be described by the following terms: PA11.
Features
Features may also be described by the following terms: Heat Stabilized, Heat-ageing Stabilized, Heat Ageing Stabilized, Heat-aging Stabilized, Heat Aging Stabilized, Low Extractables, Good Wear Resistance, Wear Resistant, Low Friction.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.