IDES Prospector Already have an account? Login Here

IDES

Toyolac® 100 X01

Acrylonitrile Butadiene Styrene

Supplied by Toray Plastics (Malaysia) Sdn. Bhd.

The technical datasheet with complete property values for Toyolac® 100 X01 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Features 
  • General Purpose
  • Good Toughness
  • High Hardness
  • High Rigidity
  • Recyclable Material
Uses 
  • General Purpose
RoHS Compliance 
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
  
Physical
Nominal Value
Unit
Test Method
Specific Gravity
      
--
 
 ASTM D792
--
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
 ISO 1133
Molding Shrinkage - Flow
in/in
 ASTM D955
Water Absorption (73°F, 24 hr)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1
Tensile Strength
      
Yield 2
psi
 ASTM D638
Yield
psi
 ISO 527-2/50
Tensile Elongation
      
Break 2
%
 ASTM D638
Break
%
 ISO 527-2/50
Flexural Modulus 3
psi
 ASTM D790
Flexural Strength
      
-- 4
psi
 ISO 178
Yield 3
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Notched Izod Impact
     ASTM D256
-22°F, 0.126 in
ft·lb/in
  
-22°F, 0.500 in
ft·lb/in
  
32°F, 0.126 in
ft·lb/in
  
32°F, 0.500 in
ft·lb/in
  
73°F, 0.126 in
ft·lb/in
  
73°F, 0.500 in
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
      
264 psi, Unannealed, 0.252 in
°F
 ASTM D648
264 psi, Unannealed, 0.500 in
°F
 ASTM D648
264 psi, Unannealed
°F
 ISO 75-2/A
CLTE - Flow
in/in/°F
 ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM C177
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity 5
ohms
 ASTM D257
Volume Resistivity (73°F)
ohm·cm
 ASTM D257
Dielectric Strength 6
V/mil
 ASTM D149
Dielectric Constant (1 kHz)
 
 ASTM D150
Dissipation Factor (1 kHz)
 
 ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Toyolac® 100 X01, Toyolac 100 X01, Toyolac® , Toyolac, Toyolac100X01, 100 X 01, 100 X01, 100X, X01, 100X01, Acrylonitrile Butadiene Styrene, ABS, Toray Plastics, AcrylonitrileButadieneStyrene, X100
Features
Features may also be described by the following terms: High Hardness, Hard, High Rigidity, Good Toughness, Tough.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Hopper Temperature
°F
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Notes
1Typical properties: these are not to be construed as specifications.
20.20 in/min
30.12 in/min
40.079 in/min
523°C
6Method A (Short-Time)
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.