IDES Prospector Already have an account? Login Here

IDES

HIPTEN® 21018A6

Low Density Polyethylene

Supplied by HIP-PetroHemija

The technical datasheet with complete property values for HIPTEN® 21018A6 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HIPTEN® 21018A6 is low density polyethylene resin developed for production of thin blown film.

HIPTEN® 21018A6 has extraordinary optical properties and very good mechanical properties, good processability and heat sealability. The addition of slip and antiblock agents results in good sliding and antiblocking properties of produced film.

HIPTEN® 21018A6 has high clarity and is suitable for packaging for a wide variety of goods.

HIPTEN® 21018A6 has Health Certificate issued by Institute for Health Protection of Serbia. Also, has Statement of Conformity, which declares product's conformity with the European norms for materials intended to come into contact with foodstuffs. Statement of Conformity is issued by Institute for Public Health, Maribor, Slovenia.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Additive 
  • Antiblock
  • Slip
  
Features 
  • Antiblocking
  • Good Heat Seal
  • Good Processability
  • High Clarity
  • Opticals
  • Recyclable Material
  • Slip
Uses 
  • Bags
  • Film
  • Packaging
Agency Ratings 
Forms 
  • Pellets
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Strength
     ISO 1184
TD: Yield, 1.5 mil
psi
  
MD: Break, 1.5 mil
psi
  
TD: Break, 1.5 mil
psi
  
Tensile Elongation
     ISO 1184
MD: Break, 1.5 mil
%
  
TD: Break, 1.5 mil
%
  
Dart Drop Impact 2 (1.5 mil)
g
 ASTM D1709A
Elmendorf Tear Strength
     ASTM D1922
MD
g
  
TD
g
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306
Optical
Nominal Value
Unit
Test Method
Gloss
 
 ASTM D2457
Haze
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HIPTEN® 21018A6, HIPTEN 21018A6, HIPTEN® , HIPTEN, HIPTEN21018A6, 21018 A 6, 21018A6, 21018A, A6, Polyethylene, Low Density, Polyethylene Low Density, LDPE, Polyethylene, PE, HIP-PetroHemija, PolyethyleneLowDensity, A21018
Features
Features may also be described by the following terms: Antiblocking, Unspecified Antiblock, High Clarity, Good Heat Seal, Slip, Unspecified Slip, Good Processability, Easy Processing.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Extrusion Notes
Blow-up ratio: 2:1 to 3:1
Notes
1Typical properties: these are not to be construed as specifications.
2F50
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.