IDES Prospector Already have an account? Login Here

IDES

HIPLEX® HUM 45010

High Density Polyethylene

Supplied by HIP-PetroHemija

The technical datasheet with complete property values for HIPLEX® HUM 45010 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HIPLEX® HUM 45010, copolymer of ethylene and hexene, with ultra high molecular weight and medium molecular weight distribution, is specially tailored for production of technical parts.

HIPLEX® HUM 45010 has very high wear resistance, very good sliding behaviour and high impact resistance even at low temperature.

HIPLEX® HUM 45010 is in granular form.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  
Features 
  • Copolymer
  • Good Processability
  • Good Wear Resistance
  • Hexene Comonomer
  • High Impact Resistance
  • Low Temperature Impact Resistance
  • Machinable
  • Med.-Wide Molecular Weight Distrib.
  • Recyclable Material
  • Ultra High Molecular Weight
Uses 
  • Engineering Parts
  • Piping
  • Rods
  • Sheet
  
Agency Ratings 
Forms 
  • Granules
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Environmental Stress-Cracking Resistance (F50)
hr
 ASTM D1693B
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
     ISO 527-2
Yield
psi
  
Break
psi
  
Tensile Strain (Break)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
 
 ISO 180
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: HIPLEX® HUM 45010, HIPLEX HUM 45010, HIPLEX® , HIPLEX, HIPLEXHUM45010, HUM 45010, HUM45010, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, HIP-PetroHemija, PolyethyleneHighDensity, 45010HUM
Features
Features may also be described by the following terms: Hexene Comonomer, Medium Molecular Weight Distribution, Wide Molecular Weight Distribution, Medium MW Distribution, Wide MW Distribution, Ultra High Molecular Weight, Ultra High MW, Good Processability, Easy Processing, Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Wear Resistance, Wear Resistant, High Impact Resistance.
Uses
Uses may also be described by the following terms: Rods, Rod, Piping, Pipe, Engineering Parts.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.