|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (150°C/21.6 kg)
|
|
g/10 min
|
ISO 1133 |
|
Elongation at Break
|
|
|
|
|
73°F 2
|
|
%
|
|
|
73°F 3
|
|
%
|
|
|
158°F 4
|
|
%
|
|
|
158°F 5
|
|
%
|
|
|
158°F 6
|
|
%
|
|
|
after 7 days: 212°F
|
|
%
|
IEC 60811-1-2 |
|
Tensile Strength
|
|
|
|
|
73°F 3
|
|
psi
|
|
|
73°F 2
|
|
psi
|
|
|
158°F 4
|
|
psi
|
|
|
158°F 5
|
|
psi
|
|
|
158°F 6
|
|
psi
|
|
|
after 7 days: 212°F
|
|
psi
|
IEC 60811-1-2 |
|
Tensile Stress (Yield)
|
|
psi
|
IEC 60811-1-1 |
|
Tensile Elongation (Break)
|
|
%
|
IEC 60811-1-1 |
|
Tear Strength
|
|
lbf/in
|
BS 6469 99.1 |
|
Durometer Hardness (Shore D)
|
|
|
ASTM D2240 |
|
Hot Pressure Test (194°F)
|
|
%
|
IEC 60811-1-3 |
|
Change in Tensile Strength in Air (212°F, 168 hr)
|
|
%
|
IEC 60811-1-2 |
|
Change in Tensile Strain at Break in Air (212°F, 168 hr)
|
|
%
|
IEC 60811-1-2 |
|
Change in Tensile Stress
|
|
|
|
|
73°F, 168 hr, in ASTM #2 Oil
|
|
%
|
|
|
73°F, 168 hr, in Diesel
|
|
%
|
|
|
158°F, 4 hr, in ASTM #2 Oil
|
|
%
|
|
|
158°F, 4 hr, in Diesel
|
|
%
|
|
|
158°F, 4 hr, in SAE 20 Oil
|
|
%
|
|
|
158°F, 168 hr, in Water
|
|
%
|
BS 6469 99.1 |
|
Change in Tensile Strain at Break
|
|
|
|
|
73°F, 168 hr, in ASTM #2 Oil
|
|
%
|
|
|
73°F, 168 hr, in Diesel
|
|
%
|
|
|
158°F, 4 hr, in ASTM #2 Oil
|
|
%
|
|
|
158°F, 4 hr, in Diesel
|
|
%
|
|
|
158°F, 4 hr, in SAE 20 Oil
|
|
%
|
|
|
158°F, 168 hr, in Water
|
|
%
|
BS 6469 99.1 |
|
Dissipation Factor (50 Hz)
|
|
|
ASTM D150 |
|
Insulation Resistance
|
|
|
BS 6469 99.2 |
|
68°F 7
|
|
ohm·cm
|
|
|
68°F
|
|
ohm·cm
|
|
|
Oxygen Index
|
|
%
|
ISO 4589-2 |
|
Acid Gas Emission Conductivity
|
|
µS/cm
|
IEC 60754-2 |
|
Acid Gas Emission pH
|
|
|
IEC 60754-2 |
|
Flammability Temperature Index
|
|
°F
|
ISO 4589-3 |
|
This supplier and product may also be known by these terms: Alpha Gary
Product names can be difficult to match. You may have searched any one of these terms to find this product: MEGOLON™ + S800, MEGOLON S800, MEGOLON™ , MEGOLON, MEGOLONS800, S 800, + S800, S800, : S800, / S800, - S800, _ S800, S800, _S800, Thermoplastic, Unspecified, Thermoplastic Unspecified, TP, Unspecified, TP Unspecified, AlphaGary, ThermoplasticUnspecified, TPUnspecified, 800S
|
|
Features may also be described by the following terms: Zero Halogen Content, Halogen Free, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle, Good Processability, Easy Processing, Good Colorability, Moisture Resistant, Water Resistant, Low Moisture Absorption, Low Water Absorption, Good Surface Finish, Low Viscosity.
|
|
Uses may also be described by the following terms: Communication Wire Insulation, Low Voltage Insulation.
|
|
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): IEC (1), BS (1), DIN (1).
|