IDES Prospector Already have an account? Login Here

IDES

4MID® 9B25500

Polyamide 6

Supplied by 4Plas

The technical datasheet with complete property values for 4MID® 9B25500 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Lubricant
  • Nucleating Agent
  
Features 
  • Lubricated
  • Nucleated
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Water Absorption
     ISO 62
Saturation, 73°F
%
  
Equilibrium, 73°F, 50% RH
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (73°F)
psi
 ISO 527-2
Tensile Stress (Yield, 73°F)
psi
 ISO 527-2
Tensile Strain (Yield, 73°F)
%
 ISO 527-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Charpy Unnotched Impact Strength
     ISO 179/eU
-22°F
 
  
73°F
 
  
Notched Izod Impact Strength
     ISO 180/1A
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature
°F
 ISO 306/B
Melting Temperature (DSC)
°F
 ISO 3146
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Comparative Tracking Index
V
 IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
     UL 94
0.0630 in
 
  
0.126 in
 
  
Glow Wire Ignition Temperature (0.0787 in)
°F
 IEC 60695-2-13
Additional Information
Nominal Value
Unit
Test Method
Filler Content
%
 ISO 3451
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: 4MID® 9B25500, 4MID 9B25500, 4MID® , 4MID, 4MID9B25500, 9 B 25500, 9B25500, 9B, B25500, Polyamide 6, Nylon 6, Polyamide, Nylon, pa6, 4Plas, Polyamide6, Nylon6, B9
Generic Name
Generic Name may also be described by the following terms: PA6.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Suggested Max Regrind
%
  
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Holding Pressure
psi
  
Injection Notes
Back Pressure: Low
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.