IDES Prospector Already have an account? Login Here

IDES

Centrene® HDF193B

High Density (HMW) Polyethylene

Supplied by Qenos Pty Ltd

The technical datasheet with complete property values for Centrene® HDF193B is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Centrene® HDF193B is a black high molecular weight bimodal PE100 High Density Polyethylene. It is a high performance resin for use in pressure pipes where service life to 100 years is required. HDF193B offers a balance of excellent processing characteristics along with outstanding toughness, chemical resistance and slow crack growth resistance . HDF193B will also provide excellent resistance to the effects of ultra-violet light exposure in outdoor applications due to well dispersed carbon black.

Centrene® HDF193B is suitable for extrusion into a full range of pipes, where High Density, PE 100 type resins are required. In particular, a broad processing window and good sag resistance enables the extrusion of larger bore, thick wall pipe. HDF193B is suitable for use in the transport of a wide range of fluids for industrial, rural and mining applications, including potable water. Suitability for use in any application should be determined by appropriate performance testing.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
Additive 
  • Carbon Black
Features 
  • Bimodal Molecular Weight Distribution
  • Good Chemical Resistance
  • Good Processability
  • Good UV Resistance
  • High Density
  • High ESCR (Stress Crack Resist.)
  • High Molecular Weight
  • Ultra High Toughness
Uses 
  • Fittings
  • Industrial Applications
  • Mining Applications
  • Outdoor Applications
  • Piping
Agency Ratings 
 
Appearance 
  • Black
Processing Method 
  • Pipe Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 Internal Method
Melt Mass-Flow Rate (MFR)
     ASTM D1238
190°C/21.6 kg
g/10 min
  
190°C/5.0 kg
g/10 min
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2 (0.0748 in)
psi
 ASTM D638
Tensile Strength 2
     ASTM D638
Yield, 0.0748 in
psi
  
Break, 0.0748 in
psi
  
Tensile Elongation 2 (Break, 0.0748 in)
%
 ASTM D638
Flexural Modulus - 1% Secant 3
psi
 ASTM D790
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D)
 
 ASTM D2240
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Centrene® HDF193B, Centrene HDF193B, Centrene® , Centrene, CentreneHDF193B, HDF 193 B, HDF193B, HDF193, 193B, Polyethylene, High Density, Polyethylene High Density, Polyethylene, High Density (HMW), Polyethylene High Density HMW, HDPE, HMW, HDPE HMW, Polyethylene, PE, Qenos, PolyethyleneHighDensityHMW, HDPEHMW, 193HDF
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, High Environmental Stress Cracking Resistance, High ESCR, Stress Cracking Resistant, High Molecular Weight, High MW, Good Processability, Easy Processing, Ultra High Toughness, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, High Density, High Specific Gravity, Bimodal, Bimodal Molecular Weight Distribution, Bimodal MW Distribution.
Uses
Uses may also be described by the following terms: Piping, Pipe.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): AS/NZS (2).
Notes
1Typical properties: these are not to be construed as specifications.
2Type IV, 2.0 in/min
30.50 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.