IDES Prospector Already have an account? Login Here

IDES

Quadrant EPP Duratron® XP (CM)

Polyamide

Supplied by Quadrant Engineering Plastic Products

The technical datasheet with complete property values for Quadrant EPP Duratron® XP (CM) is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Duratron XP is a compression-molded polyimide that offers high purity, high strength, high heat resistance, and good machinability. These properties, combined with its chemical resistance and dimensional stability, make Duratron XP ideal for components in semiconductor manufacturing and test equipment.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Acid Resistant
  • Alcohol Resistant
  • Good Chemical Resistance
  • Good Dimensional Stability
  • High Heat Resistance
  • High Purity
  • High Strength
  • Hydrocarbon Resistant
  • Machinable
  • Solvent Resistant
Uses 
  • Semiconductor Molding Compounds
Processing Method 
  • Compression Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Water Absorption
     ASTM D570
24 hr
%
  
Saturation
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ASTM D638
Tensile Strength (Ultimate)
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength (Yield)
psi
 ASTM D790
Compressive Modulus
psi
 ASTM D695
Compressive Strength (10% Strain)
psi
 ASTM D695
Coefficient of Friction (vs. Steel - Static)
 
 Internal Method
Wear Factor
10^-10 in³·min/ft·lb·hr
 ASTM D3702
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (M-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Maximum Use Temperature - Long Term, Air
°F
  
Glass Transition Temperature
°F
 ASTM D3418
CLTE - Flow 2 (-40 to 300°F)
in/in/°F
 ASTM E831
Thermal Conductivity
Btu·in/hr/ft²/°F
 ASTM F433
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity 3
ohms
 Internal Method
Dielectric Strength 4
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.125 in, Estimated Rating)
 
 UL 94
Additional Information
Nominal Value
Unit
Test Method
Limiting Pressure Velocity 5
MPa·m/s
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quadrant EPP Duratron® XP, Quadrant EPP Duratron XP, Quadrant EPP Duratron® XP (CM), Quadrant EPP Duratron XP CM, Quadrant EPP , QuadrantEPPDuratronXPCM, QuadrantEPP, EPPDuratron® XP, EPPDuratron XP, EPPDuratron® XP (CM), EPPDuratron XP CM, EPPDuratronXP, EPP, Duratron® XP, Duratron XP, EPPDuratronXPCM, Duratron® XP (CM), Duratron XP CM, DuratronXP, XPCM, DuratronXPCM, Polyamide, Unspecified, Polyamide Unspecified, Nylon, Unspecified, Nylon Unspecified, Polyamide, Nylon, Quadrant, PolyamideUnspecified, NylonUnspecified, XPDuratron, XPEPPDuratron
Features
Features may also be described by the following terms: Good Chemical Resistance, Chemical Resistant, Good Dimensional Stability, Dimensionally Stable, High Heat Resistance, High Purity, High Strength.
Notes
1Typical properties: these are not to be construed as specifications.
268°F
3EOS/ESD S11.11
4Method A (Short-Time)
54:1 safety factor
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.