IDES Prospector Already have an account? Login Here

IDES

Quadrant EPP CESTIDUR® PE-UHMW

Ultra High Molecular Weight Polyethylene

Supplied by Quadrant Engineering Plastic Products

The technical datasheet with complete property values for Quadrant EPP CESTIDUR® PE-UHMW is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Abrasion Resistance
  • Good Toughness
  • Good Wear Resistance
  • Ultra High Molecular Weight
 
Uses 
  • Bearings
  • General Purpose
 
Appearance 
  • Blue
  • Grey
 
Forms 
  • Disc
  • Rod
  • Sheet
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Water Absorption (Saturation, 73°F, 0.0394 in)
%
ISO 62
Molecular Weight
g/mol
 
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
ISO 527-2/1B/1
Tensile Stress (Yield)
psi
ISO 527-2/1B/50
Tensile Strain (Yield)
%
ISO 527-2/1B/50
Nominal Tensile Strain at Break
%
ISO 527-2/1B/50
Compressive Stress
    ISO 604/1
1% Strain
psi
 
2% Strain
psi
 
5% Strain
psi
 
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     
-- 2
ft·lb/in²
Internal Method
Partial Break
ft·lb/in²
ISO 179/1eA
Charpy Unnotched Impact Strength
 
ISO 179/1eU
Hardness
Nominal Value
Unit
Test Method
Shore Hardness
    ISO 868
Shore D, 15 sec
 
 
Shore D, 3 sec
 
 
Ball Indentation Hardness
psi
ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
ISO 75-2/A
Max. Continuous Use Temperature
     
-- 3
°F
 
-- 4
°F
 
Vicat Softening Temperature
°F
ISO 306/B
Melting Temperature
°F
ISO 11357-3
CLTE - Flow (73 to 212°F)
in/in/°F
 
Thermal Conductivity (73°F)
Btu·in/hr/ft²/°F
 
Service Temperature - Minimum
°F
 
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
IEC 60093
Volume Resistivity
ohm·cm
IEC 60093
Relative Permittivity
    IEC 60250
100 Hz
 
 
1 MHz
 
 
Dissipation Factor
    IEC 60250
100 Hz
 
 
1 MHz
 
 
Comparative Tracking Index
V
IEC 60112
Electric Strength (0.0394 in, in Oil)
V/mil
IEC 60243-1
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
UL 94
Oxygen Index
%
ISO 4589-2
Additional Information
Nominal Value
Unit
Test Method
Relative Weight Loss
    Internal Method
-- 5
 
 
-- 6
 
 
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quadrant EPP CESTIDUR® PE-UHMW, Quadrant EPP CESTIDUR PEUHMW, Quadrant EPP , QuadrantEPPCESTIDURPEUHMW, QuadrantEPP, CESTIDUR® PE, CESTIDUR PE, EPPCESTIDUR® PE-UHMW, EPPCESTIDUR PEUHMW, EPPCESTIDUR® PE:UHMW, EPPCESTIDUR® PE/UHMW, EPPCESTIDUR® PE+UHMW, EPPCESTIDUR® PE_UHMW, EPPCESTIDUR® PE UHMW, EPPCESTIDURPE, EPPCESTIDUR® PE, EPPCESTIDUR PE, EPPCESTIDURPEUHMW, EPPCESTIDUR PE_UHMW, EPPCESTIDUR PE UHMW, CESTIDUR® PE-UHMW, CESTIDUR PEUHMW, CESTIDUR® PE:UHMW, CESTIDUR® PE/UHMW, CESTIDUR® PE+UHMW, CESTIDUR® PE_UHMW, CESTIDUR® PE UHMW, CESTIDURPE, PEUHMW, EPPCESTIDURPE_UHMW, CESTIDURPEUHMW, CESTIDUR PE_UHMW, CESTIDUR PE UHMW, CESTIDURPE_UHMW, Polyethylene, Ultra High Molecular Weight, Polyethylene Ultra High Molecular Weight, UHMWPE, Polyethylene, PE, Quadrant, PolyethyleneUltraHighMolecularWeight, PECESTIDUR, PEEPPCESTIDUR
Features
Features may also be described by the following terms: Good Wear Resistance, Wear Resistant, Good Toughness, Tough, Good Abrasion Resistance, Abrasion Resistant, Ultra High Molecular Weight, Ultra High MW.
Notes
1Typical properties: these are not to be construed as specifications.
2Double 15° notch, DIS 11542-2
320000 hrs
4Short periods
5Wear test on plastics pin on rotating steel disk-tribo system
6Wear test in sand/water slurry
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.