IDES Prospector Already have an account? Login Here

IDES

Quadrant EPP CESTIFLAME PE-UHMW

Ultra High Molecular Weight Polyethylene

Supplied by Quadrant Engineering Plastic Products

The technical datasheet with complete property values for Quadrant EPP CESTIFLAME PE-UHMW is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antistatic
  • Flame Retardant
  
Features 
  • Antistatic
  • Flame Retardant
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good UV Resistance
  • Good Wear Resistance
  • Halogen Free
  • High Impact Resistance
  • Low Friction
  • Ultra High Molecular Weight
Uses 
  • Industrial Applications
Forms 
  • Disc
  • Preformed Parts
  • Sheet
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Water Absorption (Saturation, 73°F, 0.0394 in)
%
 ISO 62
Molecular Weight
g/mol
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1B/1
Tensile Stress (Yield)
psi
 ISO 527-2/1B/50
Tensile Strain (Yield)
%
 ISO 527-2/1B/50
Nominal Tensile Strain at Break
%
 ISO 527-2/1B/50
Compressive Stress
     ISO 604/1
5% Strain
psi
  
2% Strain
psi
  
1% Strain
psi
  
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (Partial Break)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength
 
 ISO 179/1eU
Hardness
Nominal Value
Unit
Test Method
Shore Hardness
     ISO 868
Shore D, 15 sec
 
  
Shore D, 3 sec
 
  
Ball Indentation Hardness
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Max. Continuous Use Temperature
      
-- 2
°F
  
-- 3
°F
  
Melting Temperature
°F
 ISO 11357-3
CLTE - Flow (73 to 212°F)
in/in/°F
  
Service Temperature - Minimum
°F
  
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohms
 IEC 60093
Volume Resistivity
ohm·cm
 IEC 60093
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.394 in)
 
 UL 94
Oxygen Index
%
 ISO 4589-2
Additional Information
Nominal Value
Unit
Test Method
Relative Weight Loss
     Internal Method
-- 4
 
  
-- 5
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quadrant EPP CESTIFLAME PE-UHMW, Quadrant EPP CESTIFLAME PEUHMW, Quadrant EPP , QuadrantEPPCESTIFLAMEPEUHMW, QuadrantEPP, CESTIFLAME PE, EPPCESTIFLAME PE-UHMW, EPPCESTIFLAME PEUHMW, EPPCESTIFLAME PE:UHMW, EPPCESTIFLAME PE/UHMW, EPPCESTIFLAME PE+UHMW, EPPCESTIFLAME PE_UHMW, EPPCESTIFLAME PE UHMW, EPPCESTIFLAMEPE, EPPCESTIFLAME PE, EPPCESTIFLAMEPEUHMW, CESTIFLAME PE-UHMW, CESTIFLAME PEUHMW, CESTIFLAME PE:UHMW, CESTIFLAME PE/UHMW, CESTIFLAME PE+UHMW, CESTIFLAME PE_UHMW, CESTIFLAME PE UHMW, CESTIFLAMEPE, PEUHMW, EPPCESTIFLAMEPE_UHMW, CESTIFLAMEPEUHMW, CESTIFLAMEPE_UHMW, Polyethylene, Ultra High Molecular Weight, Polyethylene Ultra High Molecular Weight, UHMWPE, Polyethylene, PE, Quadrant, PolyethyleneUltraHighMolecularWeight, PECESTIFLAME, PEEPPCESTIFLAME
Features
Features may also be described by the following terms: Ultra High Molecular Weight, Ultra High MW, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant, High Impact Resistance, Low Friction, Good Wear Resistance, Wear Resistant, Zero Halogen Content, Halogen Free, Good Abrasion Resistance, Abrasion Resistant, Good Chemical Resistance, Chemical Resistant.
Notes
1Typical properties: these are not to be construed as specifications.
220000 hrs
3Short periods
4Wear test in sand/water slurry
5Wear test on plastics pin on rotating steel disk-tribo system
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.