IDES Prospector Already have an account? Login Here

IDES

Safrene® M 5010

High Density Polyethylene

Supplied by Safripol (PTY) LTD

The technical datasheet with complete property values for Safrene® M 5010 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
HDPE M 5010 Polyethylene Resin is a high molecular mass grade especially developed for pressure pipe applications. HDPE M 5010 Polyethylene Resin has good impact strength, abrasion, chemical and UV resistance properties. HDPE M 5010 Polyethylene Resin is suitable for small and large diameter pressure pipe applications where compliance with ISO 4427 is required. HDPE M 5010 Polyethylene Resin is also recommended for sheet extrusion.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
Features 
  • Food Contact Acceptable
  • Good Abrasion Resistance
  • Good Chemical Resistance
  • Good Impact Resistance
  • Good UV Resistance
  • High Molecular Weight
Uses 
  • Irrigation Applications
  • Piping
  • Sheet
Agency Ratings 
Processing Method 
  • Extrusion
  • Pipe Extrusion
  • Sheet Extrusion
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR)
     ISO 1133
190°C/21.6 kg
g/10 min
  
190°C/5.0 kg
g/10 min
  
Viscosity Number (Reduced Viscosity)
ml/g
 ISO 1628
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress
     ISO 527-2/50
Yield, Compression Molded
psi
  
Break, Compression Molded
psi
  
Tensile Strain (Break, Compression Molded)
%
 ISO 527-2/50
Flexural Strength (3.5% Strain, Compression Molded)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179
-22°F, Compression Molded
ft·lb/in²
  
73°F, Compression Molded
ft·lb/in²
  
Hardness
Nominal Value
Unit
Test Method
Shore Hardness (Shore D, Compression Molded)
 
 ISO 868
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/B
Peak Crystallization Temperature (DSC)
°F
 ISO 3146
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Safrene® M 5010, Safrene M 5010, Safrene® , Safrene, SafreneM5010, M 5010, M5010, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Safripol , PolyethyleneHighDensity, 5010M
Features
Features may also be described by the following terms: Good Abrasion Resistance, Abrasion Resistant, Good Chemical Resistance, Chemical Resistant, Good Impact Resistance, High Molecular Weight, High MW, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Uses
Uses may also be described by the following terms: Piping, Pipe.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Unannealed
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.