IDES Prospector Already have an account? Login Here

IDES

Safron® H504-12M

Polypropylene Homopolymer

Supplied by Safripol (PTY) LTD

The technical datasheet with complete property values for Safron® H504-12M is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Safron® H504-12M Polypropylene Resin is recommended for the spinning of staple fibre in the range 2 - 25 denier. It is also used for the manufacture of BCF yarns.

Safron® H504-12M Polypropylene Resin is a medium to high flow injection moulding grade for applications where rigidity and fast cycle times are essential.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
Features 
  • Fast Molding Cycle
  • Food Contact Acceptable
  • Good Flow
  • Homopolymer
  • Medium Rigidity
Uses 
  • BCF Yarn
  • Fibers
  • Flooring Maintenance/Repair
  • High Tenacity Flat Yarn
  • Staple Fibers
Agency Ratings 
 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield, Injection Molded)
psi
 ISO 527-2
Tensile Strain (Yield, Injection Molded)
%
 ISO 527-2
Flexural Modulus (Injection Molded)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F, Injection Molded)
ft·lb/in²
 ISO 179/1eA
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 2
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature 2
°F
 ISO 306/B
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Safron® H504-12M, Safron H50412M, Safron® , Safron, SafronH50412M, H 504, H 504 12 M, H504-12M, H50412M, H504:12M, H504/12M, H504+12M, H504_12M, H504 12M, H504, 50412, 12M, Polypropylene Homopolymer, PP Homopolymer, Polypropylene, PP, Safripol , PolypropyleneHomopolymer, PPHomopolymer, 504H
Features
Features may also be described by the following terms: Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle, Good Flow, Medium Rigidity, Good Rigidity.
Uses
Uses may also be described by the following terms: Staple Fibers, Staple Fiber, Flooring Maintenance, Flooring Repair, Floor Maintenance, Floor Repair, BCF Yarn, Flat High Tenacity Yarn.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1).
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Injection Notes
Zone 4 Temperature: 250°C
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Injection Molded
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.