IDES Prospector Already have an account? Login Here

IDES

Safron® H510-02

Polypropylene Homopolymer

Supplied by Safripol (PTY) LTD

The technical datasheet with complete property values for Safron® H510-02 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Safron® H510-02 Polypropylene Resin is a homopolymer suitable for extrusion, general purpose injection and blow moulding. It offers good processability and low water carry-over, required when water baths are used during processing.

Safron® H510-02 Polypropylene Resin offers good tenacity and low fibrillation.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
Features 
  • Food Contact Acceptable
  • Good Processability
  • Homopolymer
  • Low Water Carryover
  
Uses 
  • Carpet Backing
  • Closures
  • Fibers
  • Monofilaments
  • Strapping
  • Tape
Agency Ratings 
 
Appearance 
  • Natural Color
Processing Method 
  • Blow Molding
  • Extrusion
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)
g/10 min
 ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Stress (Yield, Injection Molded)
psi
 ISO 527-2
Tensile Strain (Yield, Injection Molded)
%
 ISO 527-2
Flexural Modulus (Injection Molded)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F, Injection Molded)
ft·lb/in²
 ISO 179/1eA
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 2
      
66 psi, Unannealed
°F
 ISO 75-2/B
264 psi, Unannealed
°F
 ISO 75-2/A
Vicat Softening Temperature 2
°F
 ISO 306/B
Additional Information
Blow Molding conditions:
  • Zone 1: 180 to 200°C
  • Zone 2: 210 to 230°C
  • Zone 3: 230 to 250°C
  • Zone 4: 220 to 240°C
  • Die: 220°C
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Safron® H510-02, Safron H51002, Safron® , Safron, SafronH51002, H 510, H 510 02, H510-02, H51002, H510:02, H510/02, H510+02, H510_02, H510 02, H510, 51002, Polypropylene Homopolymer, PP Homopolymer, Polypropylene, PP, Safripol , PolypropyleneHomopolymer, PPHomopolymer, 510H
Features
Features may also be described by the following terms: Good Processability, Easy Processing, Low Water Carryover.
Uses
Uses may also be described by the following terms: Monofilaments, Monofilament.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1).
Injection
Nominal Value
Unit
 
Rear Temperature
°F
  
Middle Temperature
°F
  
Front Temperature
°F
  
Nozzle Temperature
°F
  
Injection Notes
Zone 4 Temperature: 245°C
Extrusion
Nominal Value
Unit
 
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Die Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Injection Molded
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.