IDES Prospector Already have an account? Login Here

IDES

Geon™ Vinyl Rigid Molding M5705

Rigid Polyvinyl Chloride

Supplied by PolyOne Corporation

The technical datasheet with complete property values for Geon™ Vinyl Rigid Molding M5705 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • General Purpose
  • High Flow
  • Medium Impact Resistance
Uses 
  • Construction Applications
  • General Purpose
  • Outdoor Applications
Forms 
  • Pellets
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Molding Shrinkage - Flow
in/in
 ASTM D955
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus 2
psi
 ASTM D638
Tensile Strength 2 (Yield)
psi
 ASTM D638
Tensile Elongation 2 (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
     ASTM D256A
0°F, 0.125 in, Injection Molded
ft·lb/in
  
32°F, 0.125 in, Injection Molded
ft·lb/in
  
73°F, 0.125 in, Injection Molded
ft·lb/in
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, 15 sec)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
     ASTM D648
66 psi, Unannealed, 0.125 in
°F
  
66 psi, Annealed, 0.125 in
°F
  
264 psi, Unannealed, 0.125 in
°F
  
264 psi, Annealed, 0.125 in
°F
  
Additional Information
Nominal Value
Unit
Test Method
Relative Spiral Flow
in
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Geon™ Vinyl Rigid Molding M5705, Geon Vinyl Rigid Molding M5705, Geon™ Vinyl Rigid Molding , Geon Vinyl Rigid Molding, GeonVinylRigidMoldingM5705, GeonVinylRigidMolding, MoldingM 5705, MoldingM5705, Molding, M 5705, M5705, Polyvinyl Chloride, Rigid, Polyvinyl Chloride Rigid, PVC, Rigid, PVC Rigid, Polyvinyl Chloride, PVC, PolyOne, PolyvinylChlorideRigid, PVCRigid, PolyvinylChloride, 5705M, 5705MoldingM
Features
Features may also be described by the following terms: High Flow, High Melt, High MFI, Medium Impact Resistance.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Type I, 2.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.