IDES Prospector Already have an account? Login Here

IDES

Versaflex™ HC MT224

Thermoplastic Elastomer

Supplied by GLS Thermoplastic Elastomers

The technical datasheet with complete property values for Versaflex™ HC MT224 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Versaflex™ HC MT224 is an exceptionally clear, high performance TPE developed for medical tubing for healthcare. Versaflex™ HC MT224 has been specially formulated without the use of any plasticizers.
New Product. Commercial specifications have not been established.
  • Flexible
  • Formulated without plasticizers
  • High Clarity
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • North America
  • South America
Features 
  • Good Flexibility
  • High Clarity
  
Uses 
  • Medical/Healthcare Applications
  • Tubing
  
Agency Ratings 
 
RoHS Compliance 
Appearance 
  • Clear/Transparent
Forms 
  • Pellets
Processing Method 
  • Extrusion
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Films
Nominal Value
Unit
Test Method
Oxygen Permeability (70°F, 73 mil)
cm³·mil/100in²/atm/24 hr
 ASTM D3985
Elastomers
Nominal Value
Unit
Test Method
Tensile Stress 2, 3
     ASTM D412
100% Strain, 73°F
psi
  
300% Strain, 73°F
psi
  
Tensile Strength 2, 3 (Break, 73°F)
psi
 ASTM D412
Tensile Elongation 2, 3 (Break, 73°F)
%
 ASTM D412
Compression Set
     ASTM D395B
72°F, 22.0 hr
%
  
113°F, 22.0 hr
%
  
158°F, 22.0 hr
%
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore A, 10 sec)
 
 ASTM D2240
Fill Analysis
Nominal Value
Unit
Test Method
Apparent Viscosity
     ASTM D3835
392°F, 1340 sec^-1
Pa·s
  
392°F, 11200 sec^-1
Pa·s
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Versaflex™ HC MT224, Versaflex HC MT224, Versaflex™ , Versaflex, VersaflexHCMT224, HC MT 224, HC MT224, HCMT, MT224, HCMT224, Thermoplastic Elastomer, TPE, GLS, ThermoplasticElastomer, MTHC
Features
Features may also be described by the following terms: High Clarity, Good Flexibility, Flexible.
Uses
Uses may also be described by the following terms: Medical Applications, Tubing, Tube.
Agency Ratings
This plastic material has 4 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): ISO (2), FDA (1), USP (1).
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
Color concentrates with polypropylene (PP), ethylene vinyl acetate (EVA), or low density polyethylene (PE) carriers are most suitable for coloring Versaflex™ HC MT224. Improved color dispersion can be achieved by using higher melt flow concentrates (with a melt flow from 25 - 40g/10 min). Typical loadings for color concentrates are 1% to 5% by weight. Liquid color can be used, but mineral oil based carriers may have a significant effect on the final hardness value. Concentrates based on PVC should not be used. A high color match consistency can be obtained by using precolored compounds available from GLS. The final determination of color concentrate suitability should be determined by customer trials.

Purge thoroughly before and after use of this product with a low flow (0.5 - 2.5 MFR) polyethylene (PE) or polypropylene (PP).

Drying is not Required

Rear: 330F-370F
Center: 350F-400F
Front: 360F-420F
Screw: 100-500RPM
Notes
1Typical properties: these are not to be construed as specifications.
2Die C
32 hr
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.