IDES Prospector Already have an account? Login Here

IDES

Bio-Flex® F 2110

Polylactic Acid

Supplied by FKuR Kunststoff GmbH

The technical datasheet with complete property values for Bio-Flex® F 2110 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Bio-Flex ® F 2110 (prev. Bio-Flex® 467F)
Biodegradable compound for film extrusion
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Biodegradable
  • Compostable
  • Food Contact Acceptable
Uses 
  • Film
Agency Ratings 
 
Forms 
  • Pellets
Processing Method 
  • Film Extrusion
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Apparent Density
g/cm³
 ISO 60
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Moisture (1.2 mil)
g/100 in²/24 hr
 ISO 15106-3
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2
Tensile Stress (Yield)
psi
 ISO 527-2
Tensile Strain (Yield)
%
 ISO 527-2
Flexural Modulus
psi
 ISO 178
Flexural Strength (3.5% Strain)
psi
 ISO 178
Flexural Strain at Break
 
 ISO 178
Tensile Strain at Break
 
 ISO 527
Tensile Strength at Break
 
 ISO 527
Films
Nominal Value
Unit
Test Method
Nitrogen Permeability (1.2 mil)
cm³/m²/bar/24 hr
 DIN 53380-2
Oxygen Permeability (1.2 mil)
cm³/m²/bar/24 hr
 ISO 15105-2
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
 ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
 ISO 179/1eU
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature (DSC)
°F
 ISO 3146
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Bio-Flex® F 2110, BioFlex F 2110, Bio-Flex® , BioFlex, Bio:Flex®, Bio/Flex®, Bio+Flex®, Bio_Flex®, Bio Flex®, BioFlexF2110, Bio_Flex, Bio Flex, F 2110, F2110, Polylactic Acid, PLA, FKuR, PolylacticAcid, 2110F
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EN (1), EU (1).
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Suggested Max Moisture
%
  
Cylinder Zone 1 Temp.
°F
  
Cylinder Zone 2 Temp.
°F
  
Cylinder Zone 3 Temp.
°F
  
Cylinder Zone 4 Temp.
°F
  
Adapter Temperature
°F
  
Melt Temperature
°F
  
Die Temperature
°F
  
Extrusion Notes
Water jacket (feed): 35 °C
Die gap: 0.8 - 1.4 mm
Die diameter: up to 400 mm
Blow film ratio: 2.5 - 4
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.