IDES Prospector Already have an account? Login Here

IDES

Biograde® C 7500 CL

Cellulose Acetate

Supplied by FKuR Kunststoff GmbH

The technical datasheet with complete property values for Biograde® C 7500 CL is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Biograde® C 7500 CL (prev. Biograde® 200 C)
Biodegradable compound for injection moulding made primarily from renewable resources.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Biodegradable
  • Renewable Resource Content
 
Agency Ratings 
Appearance 
  • Clear/Transparent
Forms 
  • Pellets
Processing Method 
  • Injection Molding
  • Sheet Extrusion
  • Thermoforming
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Apparent Density
g/cm³
ISO 60
Melt Mass-Flow Rate (MFR) (230°C/5.0 kg)
g/10 min
ISO 1133
Melt Volume-Flow Rate (MVR) (230°C/5.0 kg)
in³/10min
ISO 1133
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
ISO 527-2
Tensile Stress
    ISO 527-2
Yield
psi
 
Break
psi
 
Tensile Strain (Break)
%
ISO 527-2
Flexural Modulus
psi
ISO 178
Flexural Strength
psi
ISO 178
Flexural Strain at Break
 
ISO 178
Tensile Strain at Tensile Strength
%
ISO 527
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
ISO 179/1eA
Charpy Unnotched Impact Strength (73°F)
 
ISO 179/1eU
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
ISO 306/A
Melting Temperature (DSC)
°F
ISO 3146
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Biograde® C 7500 CL, Biograde C 7500 CL, Biograde® , Biograde, BiogradeC7500CL, C 7500 CL, C7500, 7500CL, C7500CL, Cellulose Acetate, CA, FKuR, CelluloseAcetate, 7500C
Features
Features may also be described by the following terms: Renewable Resources, From Renewable Resources, Renewable Resource Derived, Renewable Raw Materials, Renewable Resource Content.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Suggested Max Moisture
%
 
Suggested Max Regrind
%
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Injection Pressure
psi
 
Injection Rate
 
 
Back Pressure
psi
 
Injection Notes
Feed zone: 60°C
Cylinder kneeling temp: 165°C
Screw peripheral velocity: up to 200 mm/s
Shot volume: 1 until 3 D -
Holding pressure level: 40 to 70%
Holding pressure time: short
Melt cushion (of volume): 5 to10%
Cooling time: short [-]
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.