IDES Prospector Already have an account? Login Here

IDES

NatureFlex™ 90 NE

Regenerated Cellulose

Supplied by Innovia Films Ltd.

The technical datasheet with complete property values for NatureFlex™ 90 NE is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Antistatic
  • Biodegradable
  • Compostable
  • Deadfold and Twist Retention
  • Flavor & Aroma Barrier
  • Gas Barrier
  • Good Heat Seal
  • Grease Resistant
  • High Clarity
  • High Gloss
  • Oil Resistant
  • Renewable Resource Content
Uses 
  • Film
Agency Ratings 
 
Appearance 
  • Clear/Transparent
Forms 
  • Film
Mechanical
Nominal Value
Unit
Test Method
Coefficient of Friction 2 (vs. Itself - Dynamic)
 
 ASTM D1894
Films
Nominal Value
Unit
Test Method
Secant Modulus
     ASTM D882
1% Secant, MD: 0.92 mil
psi
  
1% Secant, TD: 0.92 mil
psi
  
Tensile Strength
     ASTM D882
MD: Yield, 0.92 mil
psi
  
TD: Yield, 0.92 mil
psi
  
Tensile Elongation
     ASTM D882
MD: Break, 0.92 mil
%
  
TD: Break, 0.92 mil
%
  
Seal Strength 2
lbf/in
 Internal Method
Seal Initiation Temperature (0.92 mil)
°F
 Internal Method
Oxygen Transmission Rate (Wet) (75°F, 0.92 mil, 0.0% RH)
cm³/100 in²/24 hr
 ASTM F1927
Water Vapor Transmission 3
g/100 in²/24 hr
 ASTM E96
Film Gauge
mil
 Internal Method
Yield (0.9 mil)
in²/lb
 Internal Method
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 0.920 mil)
 
 ASTM D2457
Haze 4 (0.920 mil)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: NatureFlex™ 90 NE, NatureFlex 90 NE, NatureFlex™ , NatureFlex, NatureFlex90NE, 90 NE, 90NE, Cellulose, Regenerated, Cellulose Regenerated, Cellulose Acetate, CA, Innovia Films, CelluloseRegenerated, CelluloseAcetate, NE90
Features
Features may also be described by the following terms: Good Heat Seal, Flavor & Aroma Barrier, Flavor Barrier, Aroma Barrier, Flavor and Aroma Barrier, Gas Barrier, High Clarity, Deadfold Retention, Twist Retention, Deadfold and Twist Retention, High Gloss, Renewable Resources, From Renewable Resources, Renewable Resource Derived, Renewable Raw Materials, Renewable Resource Content.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EN (1), ASTM (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Thickness: 0.92 mil
3100°F, 90%RH, thickness: 0.92 mil
42.5° wide angle
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.