IDES Prospector Already have an account? Login Here

IDES

SCLAIR® IG464-U

High Density Polyethylene

Supplied by NOVA Chemicals

The technical datasheet with complete property values for SCLAIR® IG464-U is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Additive 
  • Antioxidant
  • UV Stabilizer
  
Features 
  • Antioxidant
  • Fast Molding Cycle
  • Good Impact Resistance
  • Good UV Resistance
  • High Density
  • High Stiffness
  • Low Viscosity
  • Low Warpage
Uses 
  • Crates
  • Pails
  • Thin-walled Parts
  • Tool/Tote Box
  
Agency Ratings 
  •  1
  •  2
  
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ASTM D1238
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 4
     ASTM D638
Yield, Compression Molded
psi
  
Yield, Injection Molded
psi
  
Break, Compression Molded
psi
  
Break, Injection Molded
psi
  
Tensile Elongation 4
     ASTM D638
Yield, Compression Molded
%
  
Yield, Injection Molded
%
  
Break, Compression Molded
%
  
Break, Injection Molded
%
  
Flexural Modulus - 1% Secant
     ASTM D790
Compression Molded
psi
  
Injection Molded
psi
  
Hardness
Nominal Value
Unit
Test Method
Durometer Hardness (Shore D, Compression Molded)
 
 ASTM D2240
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ASTM D1525
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SCLAIR® IG464-U, SCLAIR IG464U, SCLAIR® , SCLAIR, SCLAIRIG464U, IG 464, IG 464 U, IG464-U, IG464U, IG464:U, IG464/U, IG464+U, IG464_U, IG464 U, IG464, 464U, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Nova Chemicals, PolyethyleneHighDensity, 464IG
Features
Features may also be described by the following terms: High Stiffness, Low Viscosity, Good Impact Resistance, Low Warpage, Low Warp, High Density, High Specific Gravity, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
Uses
Uses may also be described by the following terms: Tool Box, Tote Box, Tool/Tote Box, Thin-walled Parts, Thin Walled Parts, Thin-wall Parts, Thin wall Parts, Thinwall Parts.
Agency Ratings
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (2).
Notes
1Conditions of use B-H
2IG464-U is subject to the specific limitation that it may contact food only at temperatures of 212°F and below.
3Typical properties: these are not to be construed as specifications.
42.0 in/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.