WPP PP PPH2TF3-White Washington Penn Polypropylene Homopolymer (Talc Filler, 30%)

Product Description

Properties shown below are typical for a 30% talc filled homopolymer based compound. Additional products are offered with properties tailored for specific applications.

Custom Colors & Versions of this product available.
Approve to: Siemens SN 57916-15

General

Material Status

Commercial: Active

Availability

North America

Filler / Reinforcement

Talc Filler, 30% Filler by Weight

Features

Homopolymer

Uses

Automotive Applications

Appearance

Colors Available

White

Processing Method

Injection Molding

Physical	Nominal Value	Unit	Test Method
Density		g/cm³	ISO 1183
Melt Mass-Flow Rate (MFR) (230°C/2.16 kg)		g/10 min	ISO 1133
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (73°F)		psi	ISO 527-2/1
Tensile Stress (Yield, 73°F)		psi	ISO 527-2/50
Tensile Strain (Yield, 73°F)		%	ISO 527-2/50
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (73°F)		ft·lb/in²	ISO 179
Unnotched Izod Impact Strength (73°F)		ft·lb/in²	ISO 180
Thermal	Nominal Value	Unit	Test Method
Heat Deflection Temperature (66 psi, Unannealed)		°F	ISO 75-2/B
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: WPP PP PPH2TF3-White, WPP PP PPH2TF3White, WPP PP , WPPPPPPH2TF3White, WPPPP, PPH 2 TF 3, PPPPH 2 TF 3 White, PPPPH 2 TF 3, PPH2TF3, PPPPH2TF3-White, PPPPH2TF3White, PPPPH2TF3:White, PPPPH2TF3/White, PPPPH2TF3+White, PPPPH2TF3_White, PPPPH2TF3 White, PPPPH2, PPPPH2TF3, PPH 2 TF 3 White, PPH2TF3-White, PPH2TF3White, PPH2TF3:White, PPH2TF3/White, PPH2TF3+White, PPH2TF3_White, PPH2TF3 White, PPH2, 2TF, TF3, 3White, Polypropylene Homopolymer, PP Homopolymer, Polypropylene, PP, Washington Penn, PolypropyleneHomopolymer, PPHomopolymer, 2PPH, 2PPPPH
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.

Injection	Nominal Value	Unit
Drying Temperature		°F
Drying Time		hr
Rear Temperature		°F
Middle Temperature		°F
Front Temperature		°F
Nozzle Temperature		°F
Mold Temperature		°F
Injection Pressure		psi
Holding Pressure		psi
Back Pressure		psi
Clamp Tonnage		tons/in²
Cushion		in
Injection Notes
Injection Speed: 1.5-2.5in/s Hot Runner Temperature: 450-480°F Hydraulic Oil Temperature: 110-125°F Shot Capacity vs. Barrel Capacity: 2.5 to 4.0 Screw Decompression: 0.10in. to 0.25in. Barrel Zone 4: 450 to 460°C

Notes

¹Typical properties: these are not to be construed as specifications.

WPP PP PPH2TF3-White

Polypropylene Homopolymer

Talc Filler, 30%

Supplied by Washington Penn Plastic Co. Inc.