IDES Prospector Already have an account? Login Here

IDES

Ultrason® E 2010 MR GR 30359

Polyethersulfone

Supplied by BASF Corporation

The technical datasheet with complete property values for Ultrason® E 2010 MR GR 30359 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Agency Ratings 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
lb/in³
 ISO 1183 2
Melt volume-flow rate (360°C/10.0 kg)
in³/10min
 ISO 1133 2
Molding Shrinkage     ISO 2577 2
Flow
%
  
Across Flow
%
  
Water Absorption     ISO 62 2
Saturation
%
  
Equilibrium
%
  
Viscosity number
cm³/g
 ISO 307, 1157, 1628 2
Mechanical
Nominal Value
Unit
Test Method
Tensile modulus
psi
 ISO 527-2 2
Tensile Stress (Yield)
psi
 ISO 527-2 2
Tensile Strain (Yield)
%
 ISO 527-2 2
Impact
Nominal Value
Unit
Test Method
Charpy notched impact strength (73°F)
ft·lb/in²
 ISO 179/1eA 2
Charpy impact strength (73°F)
 
 ISO 179/1eU 2
Notched Izod Impact Strength (73°F)
ft·lb/in²
 ISO 180/A
Hardness
Nominal Value
Unit
Test Method
Ball Indentation Hardness (H 358/30)
psi
 ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi)
°F
 ISO 75-2 2
Glass Transition Temperature 3
°F
 ISO 11357-2 2
CLTE - Flow      
73 to 176°F
in/in/°F
 ISO 11359-2
356°F
in/in/°F
 DIN 53752
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL (0.0630 in)
 
 UL 94
Additional Information
Nominal Value
Unit
Test Method
Polymer Abbreviation
 
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Ultrason® E 2010 MR GR 30359, Ultrason E 2010 MR GR 30359, Ultrason® E , Ultrason E, UltrasonE2010MRGR30359, UltrasonE, E 2010 MR GR 30359, E2010 MR GR 30359, E2010, E2010MRGR30359, 2010 MR GR 30359, 2010MR, MRGR, GR30359, 2010MRGR30359, Polyethersulfone, PESU, Polysulfone, PSU, BASF, MR2010, 2010E
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EC (1).
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Tested in accordance with ISO 10350. 23°C/50%r.h. unless otherwise noted.
318 °F/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.