IDES Prospector Already have an account? Login Here

IDES

INEOS LLDPE LL6930AA

Linear Low Density Polyethylene

Supplied by INEOS Olefins & Polymers Europe

The technical datasheet with complete property values for INEOS LLDPE LL6930AA is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
LLDPE film products

Applications:
LL6930AA is a high rigidity cast film grade suitable as an anticling layer in co-extruded stretch film structures and for hygienic film.

Benefits and Features:
LL6930AA is a linear low density polyethylene copolymer containing hexene (C6) as the co-monomer. It offers the following properties:
  • Very high stiffness
  • Excellent overall film appearance and surface finish
  • Good balance between stiffness and puncture resistance

If corona treatment is necessary, the level should normally be in the range 38-48 mN/m.

We recommend that you consult your INEOS O&P Europe technical representative for further advice on the use of LL6930AA.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antioxidant
Features 
  • Antioxidant
  • Copolymer
  • Good Surface Finish
  • Hexene Comonomer
  • High Stiffness
  • Low Density
  • Puncture Resistant
Uses 
  • Film
  • Stretch Wrap
  
RoHS Compliance 
Processing Method 
  • Blown Film
Physical
Nominal Value
Unit
Test Method
Density 2
g/cm³
 ISO 1183/D
Melt Mass-Flow Rate (MFR) (190°C/0.325 kg)
g/10 min
 ISO 1133
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Tensile Modulus - 1% Secant (1.5 mil, Blown Film)
psi
 ISO 1184
Tensile Strength
     ISO 527-3
MD: 1.5 mil, Blown Film
psi
  
TD: 1.5 mil, Blown Film
psi
  
Tensile Elongation
     ISO 1184
MD: Break, 1.5 mil, Blown Film
%
  
TD: Break, 1.5 mil, Blown Film
%
  
Dart Drop Impact (1.5 mil, Blown Film)
g
 ASTM D1709A
Elmendorf Tear Strength 3
     ASTM D1922
MD: 1.5 mil
lbf/in
  
TD: 1.5 mil
lbf/in
  
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 1.50 mil, Blown Film)
 
 ASTM D2457
Haze (1.50 mil, Blown Film)
%
 ASTM D1003
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: INEOS LLDPE LL6930AA, INEOS LLDPE , INEOSLLDPELL6930AA, INEOSLLDPE, LLDPELL 6930 AA, LLDPELL6930AA, LLDPELL6930, LLDPE, LL 6930 AA, LL6930AA, LL6930, 6930AA, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, Ineos Polyolefins, PolyethyleneLinearLowDensity, 6930LL, 6930LLDPELL
Features
Features may also be described by the following terms: Hexene Comonomer, High Stiffness, Good Surface Finish, Good Puncture Resistance, Puncture Resistant, Low Density, Low Specific Gravity.
Uses
Uses may also be described by the following terms: Stretch Wrap.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Conditioned according to ISO 1872/1
3Blown Film
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.