IDES Prospector Already have an account? Login Here

IDES

SABIC® LLDPE 6218BE

Linear Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LLDPE 6218BE is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LLDPE 6218BE is a high performance C6-LLDPE polymer for cast film applications. The product has been specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast films produced from SABIC® LLDPE 6218BE exhibit excellent optical properties, improved toughness, puncture resistance and tear strength. The suffix E denotes European origin.

Applications:
SABIC® LLDPE 6218BE resin is recommended for pallet stretch wrap (pre-stretch), high performance draw down films and other mono layer and coextruded film applications where high strength is required. The grade is also suggested for blending with ethylene/butene copolymer LLDPE and LDPE for improving strength.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antioxidant
Features 
  • Antioxidant
  • Good Tear Strength
  • Good Thermal Stability
  • Good Toughness
  • Opticals
  • Puncture Resistant
Uses 
  • Blending
  • Cast Film
  • Stretch Wrap
Forms 
  • Pellets
Processing Method 
  • Cast Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/A
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Film Puncture Energy (0.79 mil)
in·lb
 ASTM D5748
Instrumented Dart Impact (0.79 mil, Cast Film)
ft·lb
 ISO 7765-2
Elmendorf Tear Strength - TD (0.79 mil, Cast Film)
lbf
 ISO 6383-2
Elastic Recovery
%
 ASTM D5459
Retention Force 2
g
  
Stress Retention
%
 ASTM D5459
Ultimate Pre-stretch Level
%
  
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature
°F
 Internal Method
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 0.787 mil, Cast Film)
 
 ASTM D2457
Haze (0.787 mil, Cast Film)
%
 ASTM D1003
Additional Information
Nominal Value
Unit
Test Method
Peel Force
     ASTM D5458
-- 3
g/in
  
-- 4
g/in
  
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LLDPE 6218BE, SABIC LLDPE 6218BE, SABIC® LLDPE , SABIC LLDPE, SABICLLDPE6218BE, SABICLLDPE, LLDPE 6218 BE, LLDPE6218BE, LLDPE6218, LLDPE, 6218 BE, 6218BE, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, SABIC, PolyethyleneLinearLowDensity, BE6218, 6218LLDPE
Features
Features may also be described by the following terms: Good Toughness, Tough, Good Thermal Stability, Good Tear Strength, Good Puncture Resistance, Puncture Resistant.
Uses
Uses may also be described by the following terms: Stretch Wrap, Cast Film.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
260 sec
3200% pre-stretch
40% pre-stretch
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.