IDES Prospector Already have an account? Login Here

IDES

SABIC® LLDPE 6335BE

Linear Low Density Polyethylene

Supplied by Saudi Basic Industries Corporation (SABIC)

The technical datasheet with complete property values for SABIC® LLDPE 6335BE is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
SABIC® LLDPE 6335BE is a hexene linear low density polyethylene resin for cast film applications. The product has been specially formulated for optimum thermal stability at high temperatures used in cast film extrusion. Cast films produced from SABIC® LLDPE 6335BE exhibit excellent optical properties, toughness, puncture resistance, tear strength and stiffness. The suffix E denotes European origin.

SABIC® LLDPE 6335BE resin is recommended for use in non cling layers in pallet stretch wrap (pre-stretch), high performance draw down films and other mono layer and coextruded film applications where high strength is required.

The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/
medical applications.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Additive 
  • Antioxidant
Features 
  • Antioxidant
  • Good Stiffness
  • Good Tear Strength
  • Good Thermal Stability
  • Good Toughness
  • Hexene Comonomer
  • High Density
  • Opticals
  • Puncture Resistant
Uses 
  • Cast Film
  • Stretch Wrap
  
Forms 
  • Pellets
Processing Method 
  • Cast Film
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183/A
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
g/10 min
 ISO 1133
Films
Nominal Value
Unit
Test Method
Film Thickness - Tested
mil
  
Elastic Recovery 2 (0.8 mil)
%
 ASTM D5459
Protrusion Puncture Resistance 2 (0.8 mil)
ft·lb
 ASTM D5748
Stress Retention 2 (0.8 mil)
%
 ASTM D5459
Thermal
Nominal Value
Unit
Test Method
Vicat Softening Temperature
°F
 ISO 306/A
Melting Temperature
°F
 Internal Method
Optical
Nominal Value
Unit
Test Method
Gloss (45°, 0.787 mil, Cast Film)
 
 ASTM D2457
Haze (0.787 mil, Cast Film)
%
 ASTM D1003A
Additional Information
Nominal Value
Unit
Test Method
Dart Impact 2 (0.8 mil)
ft·lb/in
 ISO 7765-2
Tear Strength - TD 2 (0.8 mil)
lbf/in
 ISO 6383-2
Properties are determined on 20 µm cast stretch film produced on a 2 m commercial cast stretch film line: melt temperature 270 °C, chill roll temperature 20 °C and line speed 450 m/min.
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® LLDPE 6335BE, SABIC LLDPE 6335BE, SABIC® LLDPE , SABIC LLDPE, SABICLLDPE6335BE, SABICLLDPE, LLDPE 6335 BE, LLDPE6335BE, LLDPE6335, LLDPE, 6335 BE, 6335BE, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, Polyethylene, PE, SABIC, PolyethyleneLinearLowDensity, BE6335, 6335LLDPE
Features
Features may also be described by the following terms: Good Thermal Stability, Good Tear Strength, High Density, High Specific Gravity, Good Stiffness, Good Toughness, Tough, Good Puncture Resistance, Puncture Resistant, Hexene Comonomer.
Uses
Uses may also be described by the following terms: Stretch Wrap, Cast Film.
Extrusion
Nominal Value
Unit
 
Melt Temperature
°F
  
Notes
1Typical properties: these are not to be construed as specifications.
2Cast Film
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.