IDES Prospector Already have an account? Login Here

IDES

Hostaform® C 9021 GV1/30 GT

Acetal (POM) Copolymer

Glass Fiber Reinforcement, 26%

Supplied by Ticona

The technical datasheet with complete property values for Hostaform® C 9021 GV1/30 GT is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Chemical abbreviation according to ISO 1043-1: POM
Molding compound ISO 9988- POM-K, M-GNS2, 01-003, GF26

POM copolymer

Injection molding type, reinforced with ca 26 % glass fibers improved wear performance h resistance to thermal and oxidative degradation reduced therm expansion and shrinkage.

Ranges of applications: For molded parts requiring improved low wear performance while exhibiting very high strength and rigidity as well as higher hardness.

FMVSS = Federal Motor Vehicle Safety Standard (USA)
UL = Underwriters Laboratories (USA)
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Filler / Reinforcement 
  • Glass Fiber Reinforcement, 26% Filler by Weight
Features 
  • Copolymer
  • Good Wear Resistance
  • High Hardness
  • High Rigidity
  • High Strength
  • Oxidation Resistant
RoHS Compliance 
Processing Method 
  • Injection Molding
Resin ID (ISO 1043)
  • POM
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
 ISO 1183
Melt Volume-Flow Rate (MVR) (190°C/2.16 kg)
in³/10min
 ISO 1133
Molding Shrinkage
     ISO 294-4
Across Flow
%
  
Flow
%
  
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
 ISO 527-2/1A/1
Tensile Stress (Break)
psi
 ISO 527-2/1A/5
Tensile Strain (Break)
%
 ISO 527-2/1A/5
Flexural Modulus (73°F)
psi
 ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
     ISO 179/1eA
-22°F
ft·lb/in²
  
73°F
ft·lb/in²
  
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
 ISO 75-2/A
Melting Temperature 2
°F
 ISO 11357-3
CLTE
     ISO 11359-2
Flow
in/in/°F
  
Transverse
in/in/°F
  
Additional Information
Nominal Value
Unit
Test Method
ISO Type
 
 ISO 9988-1
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Hostaform® C 9021 GV1/30 GT, Hostaform C 9021 GV130 GT, Hostaform® , Hostaform, HostaformC9021GV130GT, C 9021 GV 1, C 9021 GV1, C 9021 GV 1 30 GT, C9021GV1, C 9021 GV1/30 GT, C 9021 GV130 GT, C 9021 GV1:30 GT, C 9021 GV1+30 GT, C 9021 GV1-30 GT, C 9021 GV1_30 GT, C 9021 GV1 30 GT, C9021, 9021GV, GV1, 130, 30GT, C9021GV130GT, Acetal Copolymer, Acetal Copolymer, C9021GV1_30GT, Acetal (POM) Copolymer, Acetal POM Copolymer, Acetal, pom, Ticona, AcetalPOMCopolymer, 9021C
Features
Features may also be described by the following terms: High Hardness, Hard, High Rigidity, High Strength, Good Wear Resistance, Wear Resistant.
Injection
Nominal Value
Unit
 
Processing (Melt) Temp
°F
  
Mold Temperature
°F
  
Screw L/D Ratio
 
  
Injection Notes
Standard injection moulding machines with three phase (15 to 25 D)
plasticating screws will fit.
Notes
1Typical properties: these are not to be construed as specifications.
210°C/min
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.