IDES Prospector Already have an account? Login Here

IDES

Vipel® F007-AAA-00

Vinyl Ester

Supplied by AOC, L.L.C.

The technical datasheet with complete property values for Vipel® F007-AAA-00 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
Vipel Corrosion Resistant, Low VOC, Bisphenol A, Epoxy Vinyl Ester Resin

AOC's Vipel F007 is a low VOC, bisphenol A epoxy-based vinyl ester resin dissolved in styrene.

Versatile
The Vipel F007 Series is ideally suited for use in hand lay-up, spray-up, filament winding and pultrusion processes where outstanding mechanical properties and excellent resistance to chemicals and heat are required. Wide formulating capabilities allow for use in many processes and for optimization of cost/performance.

Corrosion resistance
Refer to AOC's "Corrosion Resistant Resin Guide under product F007" for corrosion resistance information. For questions regarding suitability of a resin to any particular chemical environment, contact AOC.

Food and Drug
All resins in this datasheet are manufactured from raw materials that are listed in FDA regulation Title 21 CFR 177.2420. It is the fabricator's responsibility to also be sure that the final composite is well cured. All composites used for FDA applications should be post cured at 180°F/82°C for at least 4 hours. After post curing, laminate should be washed with soap and water and rinsed.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
  • South America
Features 
  • Food Contact Acceptable
  • Good Corrosion Resistance
 
Uses 
  • Coating Applications
  • Filaments
 
Agency Ratings 
Forms 
  • Liquid
Processing Method 
  • Filament Winding
  • Hand Lay-up
  • Pultrusion
  • Spraying
 
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 
Styrene Content
%
 
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
ASTM D638
Tensile Strength (Yield)
psi
ASTM D638
Tensile Elongation (Break)
%
ASTM D638
Flexural Modulus
psi
ASTM D790
Flexural Strength
psi
ASTM D790
Hardness
Nominal Value
Unit
Test Method
Barcol Hardness
 
ASTM D2583
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
ASTM D648
Thermoset
Nominal Value
Unit
Test Method
Thermoset Mix Viscosity 2 (77°F)
cP
 
Post Cure Time (180°F)
hr
 
Exotherm
     
Gel to Peak
min
 
Peak
°F
 
Gel Time 3 (77°F)
min
 
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Vipel® F007-AAA-00, Vipel F007AAA00, Vipel® , Vipel, VipelF007AAA00, F 007, F 007 AAA 00, F007-AAA-00, F007AAA00, F007:AAA:00, F007/AAA/00, F007+AAA+00, F007_AAA_00, F007 AAA 00, F007, 007AAA, AAA00, Vinyl Ester, Epoxy, AOC, VinylEster, 007F
Features
Features may also be described by the following terms: Good Corrosion Resistance, Corrosion Resistant.
Agency Ratings
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
Notes
1Typical properties: these are not to be construed as specifications.
2Brookfield RV viscosity spindle 2 at 20 rpm
3Gel time with 0.2% Cobalt 6%, 0.05% DMA and 1.25% MEKP
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.