IDES Prospector Already have an account? Login Here

IDES

Susteel® P-30-12

Polyphenylene Sulfide

Unspecified Filler\Reinfor.

Supplied by TOSOH Corporation

The technical datasheet with complete property values for Susteel® P-30-12 is available to members of the Prospector Plastics Database.
Register to view full datasheet.
Register to View Full Datasheet
Product Description
This grade is specialized in high filler and toughness.
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Europe
  • North America
Filler / Reinforcement 
  • Unspecified Filler\Reinfor.
Features 
  • Good Toughness
Appearance 
  • Black
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
 ASTM D792
Melt Mass-Flow Rate (MFR) (315°C/5.0 kg)
g/10 min
 ASTM D1238
Molding Shrinkage
     Internal Method
Flow
in/in
  
Across Flow
in/in
  
Water Absorption (Equilibrium)
%
 ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
 ASTM D638
Tensile Elongation (Break)
%
 ASTM D638
Flexural Modulus
psi
 ASTM D790
Flexural Strength
psi
 ASTM D790
Tensile Weld Strength
psi
 ASTM D638
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact
ft·lb/in
 ASTM D256
Unnotched Izod Impact
ft·lb/in
 ASTM D256
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
 ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
 ASTM D648
Melting Temperature
°F
 Internal Method
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
 ASTM D257
Dielectric Strength
V/mil
 ASTM D149
Dielectric Constant (1 MHz)
 
 ASTM D150
Dissipation Factor (1 MHz)
 
 ASTM D150
Comparative Tracking Index
V
 ASTM D495
Flammability
Nominal Value
Unit
Test Method
Flame Rating - UL
 
 UL 94
Additional Information
Nominal Value
Unit
Test Method
Bar Flow Length (39.4 mil)
in
 Internal Method
Related Terminology
Product names can be difficult to match. You may have searched any one of these terms to find this product: Susteel® P-30-12, Susteel P3012, Susteel® , Susteel, SusteelP3012, P-30-12, P3012, P:30:12, P/30/12, P+30+12, P_30_12, P 30 12, P30, 3012, Polyphenylene Sulfide, PPS, Tosoh, PolyphenyleneSulfide, 30P
Features
Features may also be described by the following terms: Good Toughness, Tough.
Injection
Nominal Value
Unit
 
Drying Temperature
°F
  
Drying Time
hr
  
Rear Temperature
°F
  
Middle Temperature
°F
  
Nozzle Temperature
°F
  
Mold Temperature
°F
  
Injection Pressure
psi
  
Injection Rate
 
  
Back Pressure
psi
  
Screw Speed
rpm
  
Notes
1Typical properties: these are not to be construed as specifications.
 
IDES
Copyright © 2012 IDES
The information presented on this datasheet was acquired by IDES from the producer of the material. IDES makes substantial efforts to assure the accuracy of this data. However, IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.